Search results

  1. alldodge

    Maxwell 500

    I would say it's the relay/solenoid. Had a 500 on my 94 Formula and never had the first problem in the 20+ years I owned it
  2. alldodge

    1995 Mercruiser 350 No Start

    Fuses will be close to the ECM and will either be individual or both together. In any case the fuses will have black caps over the top of the fuse. Look for black rectangular item with wires on one end. Check for 12V at the coil with key ON and when cranking
  3. alldodge

    2000 Volvo Penta 5.7 Gfi with no spark

    With a lot of codes look at the 5V circuit to see if you have exactly 5V. If lower then one of the sensors is bad. Try at looking for gray wire on throttle position or MAP
  4. alldodge

    Is this trailer repairable?

    It can be fixed, just depends on cost Most likely there is more issues they just are currently unseen
  5. alldodge

    Maxwell 500

    If it's an anchor windless (I had same model) then most likely its the relay which is normally close to the windless. Can also be the helm switch has issues or bad connection
  6. alldodge

    4.3gi no start new ICM. how to set base timing?

    With new plugs fowling, put the old injectors back in
  7. alldodge

    4.3gi no start new ICM. how to set base timing?

    Many list injectors as rebuilt and for the most part, electrical injectors can not be rebuilt, they can be cleaned up to look great. The injectors are standard GM type, but we can let this one go for now Was running rough and now it won't even start after replacing the ICM. Have you tried...
  8. alldodge

    Mounting a gen 1 alpha to a gen 2 housing.

    Looks like gimbal rings are different
  9. alldodge

    4.3gi no start new ICM. how to set base timing?

    The Gi should have a MEFI 3 ECM and Delco EST distributor You mentioned ICM, are you referring to the Distributor ICM? While the rotor would point toward number one cylinder, but it should be on the compression stroke and the timing mark on balancer would line up. Where did you get the...
  10. alldodge

    Starter options for 2000 5.0 GL?

    Here ya go https://www.dbelectrical.com/products/starter-for-marine-applications-pmgr-12-volt-cw-11-tooth-50-807904a1.html
  11. alldodge

    Wiring manual

    This is the basic wiring diagram, yours may not have the Acc switches
  12. alldodge

    2000 Volvo Penta 5.7 Gfi with no spark

    Go back to the wiring diagrams previous Check for power at the FP relay, should be 12V on 2 of the pins One of the pins go to the ECM and it should apply a ground to coil side of relay when key is turned to run/on
  13. alldodge

    2000 Doral Port-Side Window?

    Welcome I would contact Taylor Made first then Fex a Fab https://www.taylormadeproducts.com/windshield-glass-solutions/ https://flexafab.com/products/doral-curved-glass-boat-windshield-repair
  14. alldodge

    VP SX-M Carrier Bearing Seal - New Seal Missing Second Spring/Lip

    It could be the seal is no longer made and this is one which comes closest. I did find a couple of the old style available and might be new old stock. At VP site it still shows original https://www.volvopenta.com/shop/0?ft=3852272
  15. alldodge

    1976 888 Fuel Questions

    Would be my guess
  16. alldodge

    1976 888 Fuel Questions

    Running the motor above 1500 can and usually does burn the impeller. A garden hose cannot supply enough flow so impeller runs dry enough to burn
  17. alldodge

    What is a suitable replacement for MARMAC M-1093-D2 on Volvo Penta AQ170 with 270 out drive?

    Suggest contacting Seastar, they should be able to help
  18. alldodge

    New issue cropped up on my transom/bunk position!

    Your saying buy a brand new boat and then modify it?
  19. alldodge

    Verado trim cylinder

    Looking thru the manual 8M0182077 I'll say it was coincidence from hearing the pop and later see a leak. There are only O-rings that keep 2600 psi fluid from leaking. Don't see how this will last long term, and in salt will be shorter Still don't like the leak but at least now I don't see...
  20. alldodge

    Voltage low code 4602-32

    Do agree it got frustrating quick. I installed 1stmate (1st) with a NEMA connection at first while I was also installing the VHF which also used NEMA. Could be where I got into trouble is reading forum comments about 1st not using the NEMA connection even when connected. Others had contacted...
Top