Search results

  1. alldodge

    2013 Mercury 20 1F20201HK Leaking gas out the carb mouth (Solved)

    If you still have the old carb, might try this. Remove float and get a hair dryer or heat gun. Heat the plastic up so it will bend just a slight bit. Other then that I'm also clueless
  2. alldodge

    1992 mariner 150hp

    I don't know if this is correct but I've seen this comment on a few forums "Take prop off, lay it on a flat surface and measure the height difference between the leading and trailing edges of a blade, then multiply that number by number of blades. That will give you the pitch."
  3. alldodge

    1992 mariner 150hp

    Back of the prop is next to the nut
  4. alldodge

    1992 mariner 150hp

    Look at the back of the prop hub for numbers
  5. alldodge

    Older Ranger Inboard

    Welcome You posted in the VP section so is the drive a VP? Mentioned a Ford motor, how many cylinders?
  6. alldodge

    2013 Mercury 20 1F20201HK Leaking gas out the carb mouth (Solved)

    I don't see it in the part number breakdown but wonder if a spring should be on the needle. Found where a Gen carb has a spring installed At 2:47 you can see the spring
  7. alldodge

    2013 Mercury 20 1F20201HK Leaking gas out the carb mouth (Solved)

    Have not seen a entire plastic float until now https://www.crowleymarine.com/mercury/products/162532-float Needle https://www.mercruiserparts.com/809570002-float-valve Need maybe @Texasmark or @racerone help
  8. alldodge

    2013 Mercury 20 1F20201HK Leaking gas out the carb mouth (Solved)

    Welcome Readjust float so fuel is shut off a slight bit lower
  9. alldodge

    Divet/crane

    I didn't hear any say "Squirrel" but I am getting hard of hearing and didn't know Mr spell checker was on line
  10. alldodge

    1976 Montego 16- The "Free" Puppy

    No expert but appears to work. Your sensors are 240-33 ohms and spec shows Unit switching: Press the button first, then power on, and then enter the parameter selection mode. You can select the 0-190ohm(European) or 240-33ohm(American) level sensor. switch the units of speed (MPH,km/h or...
  11. alldodge

    1976 Montego 16- The "Free" Puppy

    Didn't see anything on the gauge specifying CAN Buss
  12. alldodge

    1976 Montego 16- The "Free" Puppy

    Should work good, and be way more accurate then original
  13. alldodge

    1976 Montego 16- The "Free" Puppy

    Can replace some stuff but going full modern is mostly out of the realm without some major investments to go to something like NEMA 2000. The helm also doesn't have much space available Could go with miniature gauges or quad type. Maybe install a smaller chart plotter with combo fish finder
  14. alldodge

    Divet/crane

    Might try something like, take a 2x10 and strap cross both sides of the hull. One side of the 2x10 extend out as far as you might need. With boat in the water walk out to the end of the board to see what your boat does. Might try to tip, if not your good with the balance, just need to figure...
  15. alldodge

    Divet/crane

    Welcome Yes it would need to be reinforced. A pedestal seat can hold that much weight but mainly force going downward. A davit will have much more load when the arm is extended. Greatest load will be the opposite of the arm. This is why a claw hammer can easily remove a nail
  16. alldodge

    Houston….. We’ve had a problem…..

    If it is really easy as next to nothing, look close at the splines. The splines should be square and not tapered. Should be able to slide in/out with 2 fingers
  17. alldodge

    LED light device in battery compartment

    Welcome Post a pic Select the Attach files button and upload a pic
  18. alldodge

    1974 Evinrude fisherman pull start not working

    Take it apart and grease it up. The roll pin might be binding or spring is broke or hanging
  19. alldodge

    5.7gs coolant temp sensor

  20. alldodge

    5.7gs coolant temp sensor

    The one your finding is the ECM sensor, the one with one connection is the gauge sender. The gauge sender has no effect on the motor, it's just there as a visual aid for the driver Look for a standard 240-33 ohm sender
Top