Search results

  1. Scott Danforth

    Lower Unit Gear Oil Change while on lift

    cant do the annual PM on a lift.
  2. Scott Danforth

    1 or 2 PDS bearings in my Volvo 270 outdrive

    if the floor is gone, the stringers and transom long ago rotted
  3. Scott Danforth

    Dash got ripped out!

    quick search on some of google and one from one of the surplus sites.
  4. Scott Danforth

    Dash got ripped out!

    Depends. some dash wiring is from mercruiser. most are done by outside marine instrument panel shops. the wiring should be ABYC standard colors. I would look to see if any of the marine surplus stores have a dash, then all you have to do is a bit of wiring.
  5. Scott Danforth

    projects other than boats

    No, it's going to be a carb build.
  6. Scott Danforth

    projects other than boats

    Just measured the jeep bell housing, etc. exact same length as the LNF ecotec bell housing Can go bigger than a 142 tooth ring gear. The LS4 will take a GM small pilot bearing
  7. Scott Danforth

    Need advice

    I will add, weather apps are only useful when there is cell service. cell phones do not work when you are 25+ miles off shore. having a radar on the boat is what is needed for that additionally, certain bodies of water ignore weather forecast. for example, deaths door in the bay of green bay...
  8. Scott Danforth

    1 or 2 PDS bearings in my Volvo 270 outdrive

    pull the drive and look
  9. Scott Danforth

    Gauge panel is falling out, the screws were held on with glue??

    methacrylate...... glorified superglue. its the adhesives used to bond nearly everything together in the marine world. such as plexus, sika bond, etc. pull the gauge panel, work on the bench.
  10. Scott Danforth

    projects other than boats

    Swapping motors and chassis is all easy. Just bolts and fabrication. The fact that an LS motor is shorter than the SBC makes it easy. Not sure how in this day and age anyone can charge that amount, however people have lost the ability to do their own wrenching
  11. Scott Danforth

    NEED A VP PROS OPPINION!

    Carter is an OEM supplier. About $100 from Napa or Summit
  12. Scott Danforth

    NEED A VP PROS OPPINION!

    Factory. . Airtex or Carter (same company)
  13. Scott Danforth

    projects other than boats

    Read this then .....https://www.hotrodders.com/threads/1952-fiat-topolino-belvedere-project.550685/page-2?nested_view=1&sortby=oldest And this..https://ls1tech.com/forums/generation-iv-internal-engine/1972992-cam-recommendations.html LOL. Seriously, this project will take about another 6...
  14. Scott Danforth

    Gauge panel is falling out, the screws were held on with glue??

    southbay and the other forest river brands buy their gauge panel from the same source that feeds most of the pontoon market. start by calling their customer service line. beyond that, it should be a simple repair with a methacrylate of your choice.
  15. Scott Danforth

    projects other than boats

    there are shops down here that do nothing but convert cars to LS. you supply the car, the LS motor, and parts, and for $19K in labor, they will convert your ride. based on what I know, that comes out to $500 per hour.
  16. Scott Danforth

    projects other than boats

    yes, look at Volvo-Penta, Ilmore, Indmar and PCMC (not mercruiser) all of them have both cat and non-cat exhaust
  17. Scott Danforth

    projects other than boats

    Yes. Stock bottom, Ported heads, Gnarly cam, Victor Jr clone intake, HP830 carb
  18. Scott Danforth

    Gas and Ethanol

    I leave 2-stroke oil in the saws, etc for months between use. 2-stroke oil is a much better stabilizer than stabil
  19. Scott Danforth

    Volvo Penta SX-M Trim drifting down.

    I said piston seals (internal) not gland seals (external) the blind end is bypassing the cylinder to the rod end. this could be the piston to rod seal, or this could be the piston to barrel seal. plastic/rubber cylinder seals last about 20 years and then they need replacing.
  20. Scott Danforth

    Building a tackle drawer unit

    starboard cnc routed is how they make the tackle centers are places like teak isle. I would look at the surplus folks like great lakes skipper or marine surplus and buy one.
Top