Search results

  1. S

    Motor swap- wiring questions

    See your post #10. I was explaining that the brown wires were not t&t.
  2. S

    1995 Evinrude E40ELEO RPMs

    With that year and horse power they would want you to be between 5000 and 5500 rpm's. Not 6000. Calling vdo is probably best.
  3. S

    johnson 70hp 2 stroke 1995 shut down when warm

    So your going to rebuild it?
  4. S

    johnson 70hp 2 stroke 1995 shut down when warm

    Also, not a dead blow, steel hammer
  5. S

    johnson 70hp 2 stroke 1995 shut down when warm

    No nut. You removed the nut correct?
  6. S

    johnson 70hp 2 stroke 1995 shut down when warm

    Cheap puller
  7. S

    johnson 70hp 2 stroke 1995 shut down when warm

    Your the Canadian with the blown engine right? Or did the a second compression test, test out better? Flywheels get a little stuck but tighten the main puller bolt and than tap with a hammer... It will pop like Tp says.
  8. S

    1985 evinrude 30 hp prop power issue

    If it died while hand choking then that means it's most likely not a fuel problem. Is carb valves opening fully?
  9. S

    Help

    Number 85 is your fuse on your main wiring harness.
  10. S

    1995 Evinrude E40ELEO RPMs

    I know you said that already. Motor should idle, warmed up and in the water....in gear, at 650 to 700 rpm's. Cold not in gear? 1000 wouldn't surprise me. Now 7000 at WOT? That's way off unless your prop is junk. You will need to get it back in the water to test correctly and may need to adjust...
  11. S

    1995 Evinrude E40ELEO RPMs

    Try it.
  12. S

    Help

    Pee hole could be plugged, doesn't mean it got hot. Starter button worked before? If so, wire or fuse most likely. Racerone wanted model number, maybe he's on to something. Post model number.
  13. S

    Help

    Test wires from push switch for continuity. Is wire hooked up to soloniod correctly? Why do you say motor got hot? Did you melt a wire?
  14. S

    1974 Johnson seahorse 4hp weedless running strong, then randomly dies out and takes a lot to start.

    Yes, it can be your tank. It needs a vent to continue to run.
  15. S

    1995 Evinrude E40ELEO RPMs

    Those numbers are too high. Which pole setting is that?
  16. S

    84 Evinrude bogging full throttle surge

    I was going to add this and I forgot.
  17. S

    84 Evinrude bogging full throttle surge

    I don't think it's the prop with what your saying. When the prop slips your engine over revs and your boat slows. Is that happening? Doesn't sound like it. In the past others here have stated that you should look for a damaged wire, probably one under the flywheel that is shorting out when you...
  18. S

    2003 Evinrude 250 FICT - Stumped

    Here is a post in 2013 with a similar issue, a way to test (should be able to make sure pathways are connected) and then they list a place that repairs them. Have you ever plugged in a different control box just to see if that solves it? Anyhow, enjoy the read...
  19. S

    J150EXECD shift cable vs throttle cable

    Are those xtream cables as good as advertised? Claim to be smoother. Also, you left out one step, "test engine" ; )
  20. S

    84 Evinrude bogging full throttle surge

    If it's not the prop it's got to be fuel. If your using a boat fuel tank try and use a portable one.
Top