Search results

  1. dingbat

    New to me Lazer II with 3 square PVS vent holes

    Never saw a “vented” prop with multiple holes until I bought the Enertia. Always just a single hole Here is old school Merc service bulletin on how it was done http://www.fiberglassics.com/media/kunena/attachments/legacy/images/drilling_prop.jpg
  2. dingbat

    Grady white thru hull size?

    Live well - 1-1/2” Bilge pumps -1-1/8” Drains and fish boxes -1”
  3. dingbat

    2003 Merc 200HP 2 stroke. Water Pressure Gauge Installation Question. Where to tap?

    Guessing the plugged line coming off the tee is used to feed the gauge
  4. dingbat

    Replacing Thru hull ...size??

    I would question the use of a clear, non-reinforced plastic hose but that’s just me. Thru hulls do not have hose “barbs” per say. The hose to fitting connection is a slip fit retained with hose clamps. The proper size hose should not need to be heated to install on a thru hull. Replaced every...
  5. dingbat

    Transom Corrosion & Alumacraft not honoring warranties

    I don't see that as a disingenuous reply. Everything stated is fact. Dis-similar metals (copper/aluminum) corrosion requires an electrolyte. Seeing that the splash well is involved....I'm guessing the splash well drains are leaking and you have a wet transom. Hard to tell from the picture...
  6. dingbat

    2006 225 4stroke runs poor until warmed up.

    Temp sensors are thermistors. Check the resistance while varying the temperature. Typically don’t go out of calibration per say. Typically fail open or closed.
  7. dingbat

    Can anyone help electrical question

    Need a new motor and probably a new gear box as well since RPM factors into this as well ;) The flaw in your theory is that motors are wound to a particular HP rating. One (1) HP = 714 watts. Watts = Volts X Amps With Watts fixed by the motors HP rating, increasing the voltage simply...
  8. dingbat

    Wonder if I should go IO again or go OB?

    If I wanted to listen the the rumble of engines I would have bought a house next to the freeway. I much prefer the sound of the wind whistling though the the hardtop structure...lol
  9. dingbat

    New to me Lazer II with 3 square PVS vent holes

    The last ported prop I ran only had one plug which you drilled out to suit Can’t remember if I ended up with a 5/16” or 3/8” “port”
  10. dingbat

    Wonder if I should go IO again or go OB?

    Foam has no bearing on weight capacity. The increased capacity is the direct result of reduced weight of the outboard power and the reduced size of the “massive and extended” swim platforms. The first boat back in 1994 was an I/O. Sold it in 1997 and bought an outboard..never looked back
  11. dingbat

    Battery Question

    Yes, just like the ground for every circuit in your house is tied together at the fuse box to maintain a common ground potential.
  12. dingbat

    Battery Question

    The supply should be different, but you want to keep a common ground between both batteries to prevent ground loops. Normally the (two) ground cable are tied together at a common point. Either via a dedicated bus bar or daisy chained between the battery ground posts then on to engine ground.
  13. dingbat

    Extended Warranty

    Extended warranties......they wouldn't offer "Extended Warranties" unless the odds where not well stacked against the buyer. As I sale guy I love them.........gold in the bank and money in my pocket. Only thing more lucrative are Maintenance Contracts...;)
  14. dingbat

    2006 225 4stroke runs poor until warmed up.

    I see two normal thermostats and two plug in temp sensors. Temps sensors would be checked by varying the temp and checking the resistance values where in spec. I'm guessing a factory manual would give you the procedure and pass/fail values
  15. dingbat

    Osco? Ever wonder what happened?

    Steel guy, as in steel mill, as well. Why cant you use different alloys with your molds? Unless it’s a cooling issue, you have me scratching my head.
  16. dingbat

    2006 225 4stroke runs poor until warmed up.

    Did you check to make sure the thermostats are installed and or working?
  17. dingbat

    Trailer Tires

    What was the date code on the last tire that blew? My last "couple of years" back story turned out to be 11 years May-pops turn to Will-pops on their 6 year expiration date.
  18. dingbat

    Fuel Fill Hose

    Isn't that what I said?....lol
  19. dingbat

    Seat bushings

    Are your sure about the post OD? See lots of bushings for 2-3/8 and 2-7/8 posts
  20. dingbat

    Fuel Fill Hose

    2" is typically reserved for diesel fuel. Never seen it on gasoline powered
Top