Search results

  1. jimmbo

    Do you use non ethanol gas ?

    The only shortage is caused by Oil Robber Barons, who figured out that they could make more money while providing less product. It is Simple Gouging
  2. jimmbo

    Holley Terminator fuel injected carb tuning 98 Baja Outlaw

    Holley doesn't market a Terminator FI that is USCG compliant, they do however have a few Sniper FI systems that at USCG compliant, though they require an Exhaust Sensor to operate correctly.
  3. jimmbo

    Mercury 115 EFI 2015, white "plastic ring" in front of propeller, what is it for?

    How about taking the prop off, and using a small hammer, and a small dowel, either tap it on the prop or tap it off and then reposition it on the gearcase. Reinstall Prop
  4. jimmbo

    Mercury 115 EFI 2015, white "plastic ring" in front of propeller, what is it for?

    It is used to provide a better seal to reduce/prevent Exhaust Gases from exiting at that location an causing Havoc for the Prop
  5. jimmbo

    Evinrude 1973 boat motor runs while out of the water but not in the water.

    Remove the Transfer Port Covers and take a look at the Piston and Rings. Compression Test can still be done after the Covers are off, but I doubt it will be needed
  6. jimmbo

    Help Identifying Boat! Fiberform

    Last thing you want to do is cut the Fiberglass that makes up the outside of the Transom. If you do , you will have a very weak repair as the new outer glass will only be a butt joint or a very limited overlap with the old Glass. The best repair is when the old Transom is busted up and dug out...
  7. jimmbo

    Help Identifying Boat! Fiberform

    Sometimes the Canadian made boats were slightly different in trim. A Transom shouldn't flex at all. To get the motor off, a Couple of Friends with Strong Backs and Weak Minds can be handy. That motor weighs about 290 lbs. It is pain to remove as the Power Trim hoses have to be undone. To...
  8. jimmbo

    Do you use non ethanol gas ?

    My Volvo I/O requires Midgrade, but since Costco doesn't sell a Midgrade(in Western Canada), I just fill up with Premium which doesn't have the Disclaimer about the Corn Squeezings for Premium, like they have for Regular. Here in the Summer, the Humidity hits 100% just about every night, and I...
  9. jimmbo

    Help Identifying Boat! Fiberform

    Those type of lights shouldn't be too hard to find. iboats might have something that would work. and there other like Land and Sea As for the Transom, the wood is Rotted, and needs to be replaced, Putting a Metal Plate as Reinforcement only moves and concentrates the flexing to another area. I...
  10. jimmbo

    Launching/retrieving with FWD

    I've seen lines long enough that that might have been the case
  11. jimmbo

    Launching/retrieving with FWD

    April was only 3 months ago, after 6 months, it becomes Old enough that only the OP can safely reactivate it
  12. jimmbo

    1976 25hp Johnson ignition question

    Whole Armature plate looks a little oily. Could need the upper crankshaft seal replaced. If the either of the points are dirty, no spark will happen either
  13. jimmbo

    Launching/retrieving with FWD

    I used to tow one of my older lighter boats with a little FWD Sedan DeVille. I never had a Problem with the Front End losing traction on the ramp, but the tongue weight wasn't more then 50-60 pounds. I did worry about the Transaxle, if it was strong enough for the extra 1700 lbs. I did trade it...
  14. jimmbo

    1986 50 hp 3cyl

    Welcome to iboats While it could happen, the Reeds on these engines rarely fail. Sounds like they don't know how to adjust the Timing and/or Sync on these engines. This is a 36 yr old engine, it can become a Money Pit, as the price of the parts you have already replaced cost more than the...
  15. jimmbo

    Evinrude V4 120 runs much faster once past 3500rpm

    Welcome to iboats A picture or two would certainly clear up what you are referring to
  16. jimmbo

    Prop diameter effect and planing trouble

    deleted
  17. jimmbo

    1995 Evinrude 88SPL Carb jet question

    Sounds like a heavy/misadjusted Float, or a bit of dirt contaminating the Fuel Inlet of the Carb. When reassembling, don't forget to do a Link and Sync.
  18. jimmbo

    Johnson Motors

    Completely different Powerheads, and likely midsections. As for Gearcases, I never even looked, but unlikely to swap Is this the engine I suggested you run from? Duplicate Posts on the same item are not the way to get info
  19. jimmbo

    Johnson Motors

    Still haven't told me what engines
  20. jimmbo

    1995 Evinrude 88SPL Carb jet question

    But the Parts listing say only 1 per Assembly for that engine
Top