Search results

  1. alldodge

    STUCK gimbal bearing.....

    If the bearing gets cocked even slightly it will dig into the housing. Sometimes its best to hammer it back in and see if there is a ridge I know this would be older transom then 1980, but does yours have a snap ring holding the bearing in?
  2. alldodge

    Propless?

    Most boats come with the 1.5 unless their real heavy. Props would be in the 19 and 21 pitch. The 302 not being a power house and a 25foot boat, I would go with the 19
  3. alldodge

    HELP I can't get my motor realigned

    Sounds like you have it centered Put some grease on the end of the tool. Push in until it stops, pull it out and see if it's high or low
  4. alldodge

    Propless?

    Yes, Merc is the only place and it takes someone with access the the data base to get the info of ratio.
  5. alldodge

    Missing transom bolt on Mercruser outdrive to bellhousing.

    You didn't mention which drive but I'll guess it's a R or MR but motor needs to come out, and while your at it check the transom https://www.mercruiserparts.com/bam/subassembly/30872/2203/40
  6. alldodge

    Delco EST conversion kit timing problem

    Then you should be good to go
  7. alldodge

    Delco EST conversion kit timing problem

    Does the timing advance when rpm's increase?
  8. alldodge

    1994-96 four Winns freedom 3.0 cobra belt routing

    Welcome Moved you to OMC Have never seen a belt driven water pump on a 3.0, can you post a pic?
  9. alldodge

    Propless?

    From you Remove drive, put in gear Rotate drive 10 times counting drive shaft and prop shaft rotations. This will give ratio
  10. alldodge

    Kodiak Anchor - Made by SouthCoast Marine . . .???

    Oh you have 3 strand and that's different Might need a long splice
  11. alldodge

    Help a little old lady with her little old mercruiser 120 wiring?

    Welcome I'm having a problem with Should be one brown going to interruptor Other goes to the Tach The interruptor has nothing to do with the trim pump
  12. alldodge

    proper shift bellows install.

    Everyone will need to know what drive, Alpha G1, G2, Bravo Hey @Bt Doctur might be up your alley
  13. alldodge

    Propless?

    What is your drive ratio?
  14. alldodge

    Kodiak Anchor - Made by SouthCoast Marine . . .???

    It looks a bit thick, maybe Anna can help
  15. alldodge

    Alarms and s.l.o.w mode

    Then you need another Mechanic
  16. alldodge

    Alarms and s.l.o.w mode

    Welcome The motors need to be scanned. With slow mode (guardian) and the alarm there will be a code. Mentioned going from a 5.0 to 5.7 GXI, is the 5.7 using the 5.0 ECM?
  17. alldodge

    Slave solenoid does nothing

    Manual 3 pages 3F-24 thru 3F-26
  18. alldodge

    Volvo Penta 5.0 GXI-E - Won't roll over

    Steering ram moving and not the motor running rough
  19. alldodge

    5.7 EFI stalls when warm and shifting into gear

    IMO the Mechanic didn't buy it because he's not a "actual" Tech. TBI, MPI all used MEFI's and all use the same connector
  20. alldodge

    MERCRUISER 5.0 MPI 2005 ALARM NOT MORE THAN 2500 RPM

    Motors need to be scanned for codes. Also going over 1800 rpm on a hose can burn the impeller
Top