Search results

  1. jimmbo

    high idle

    Some Control boxes, move the Cable Housing, when the Fast Idle Levers are being utilized, instead of moving the Inner Cable. Improper Anchoring of the Cable to the Boat, can interfere with its operation Improperly adjusted cable length at the Motor, can result in Inconsistent Idle, or too fast...
  2. jimmbo

    Twin 2.6 omc outboards

    What kind of Voltage is going into the Rectifiers What year are these Beasties?
  3. jimmbo

    Securing batteries in Supreme trout boat

    Boat Manufacturers should be required by Law/USCG, to engineer a Battery Hold Down Location where there is enough Structure to securely secure Batteries without risking going thru the bottom of the hull. A couple of r/8" long #6 Screws going into a 3/8" thick Plywood, isn't much for a 30lb...
  4. jimmbo

    Lower Unit Compatability

    Well, you certainly won't be participating in that Conversation/Discussion
  5. jimmbo

    Boston Whaler Prop

    Welcome to iboats Sounds like you can drop down a bit in Pitch, which will raise the RPM and improve the Hole Shot. If the tach is accurate, you are quite a ways from the 6K limit. Even though with less Pitch, which you are likely thinking, lower top speed, the engine will be running nearer it...
  6. jimmbo

    Lower Unit Compatability

    You knew how/where to look, but were just too Lazy and wanted someone else to do it for you.
  7. jimmbo

    Lower Unit Compatability

    Yet, even your second link there states "80 Jet" Well since you have your links, you can look up all the Parts #s to check Compatibility
  8. jimmbo

    Anyone Seen these?

    Scott likes Shiny Coins
  9. jimmbo

    Lower Unit Compatability

    First serial number took me to a Parts listing for a 25" Shaft The Second Serial number took me to a listing for a 4 cylinder Jet...
  10. jimmbo

    high idle

    Did it work fine before? If so, did you do anything to the Control Cables, like anchoring/securing them?
  11. jimmbo

    Anyone Seen these?

    I don't know if it any good or not. However I fed up of one Test Site which has been trying to promote that thing, like an Infomercial. Only things missing are Mike Levey and his sidekicks Ian and John. That site has never reviewed an item that is supplied by their Advertisers as being less than...
  12. jimmbo

    Anyone Seen these?

    Yeah that Sham Item has been going around for a couple of Years. There is a Site that keeps spreading a lot of Manure about that Pretzel
  13. jimmbo

    Twin 2.6 omc outboards

    What voltages are shown at the Batteries, With engine off, and with engine running at a fast Idle?
  14. jimmbo

    Building a wake boat.

    your idea of Large Waves close to the Shoreline might destroy the Nesting Areas of many Species of Birds. For that reason alone, I know my country is looking at passing Laws to prevent Wakeboard Boats being operated closer than 5 miles from any Shoreline. Really Needed and long Overdue
  15. jimmbo

    Mariner 1977 - 80cc help :D

    If the Foam was waterlogged, the odds are that the Stringers between the Hull and the Floor are rotted as well
  16. jimmbo

    Mariner 1977 - 80cc help :D

    Why did you remove the foam?
  17. jimmbo

    Warm up

    Here are a couple of pages from the 1985 Mercury Brochure
  18. jimmbo

    Warm up

    So you are pressing the Interlock on the Throttle Lever to disengage the Shift Mechanism? As the engine is warming up you may have to press the key in briefly on occasion. You say the Primer bulb is no longer getting Firm. Is there fuel dripping from the Engine as you squeeze the bulb? These...
  19. jimmbo

    Battery questions - Winner with 80 HP Johnson

    Keep in mind it is a 55 year old motor, and even after any repair/parts replacement, it is still a 55 year old motor. Have you checked to see if there is Oil and/or Water in the Gearcase? At minimum, it is going to need a new Water Pump impeller, New Gear Oil, Carb overhaul, and Ignition...
  20. jimmbo

    Warm up

    Please describe your Procedure for Starting My inline 6 got about 30 seconds of warm up at the dock, before casting off. I didn't floor it immediately, I would wait for another minute, maybe minute and a half, then it was Go Time
Top