Search results

  1. R

    2000 70hp Johnson semi start/ won’t stay running

    Did you make sure that the high speed jets ( orifice plugs ) are clean ?---They are found way inside the carburetor bowls.----Often over looked.
  2. R

    Complete removal of vro components

    It is not common to get rid of all those pieces.----I am going to look into getting rid of it on a 150 HP with 2 older 100 HP pumps,----Can't say how yet and not going to explain here how it is done for safety reasons.-----Your local dealer might help you.
  3. R

    2000 70hp Johnson semi start/ won’t stay running

    You have to wonder why it sat all those years.----Post compression values.
  4. R

    97 Force 120- Low idle at times, stalls when engaging into gear

    Nobody here can put hands on your motor.---Check head bolt torque.-----Have you adjusted low speed mixture screws ?----Information must be posted.-----Post the compression values.----Does spark jump a gap of 3/8" on all 4 leads.
  5. R

    Which bearing kits do you guys prefer?

    Most towns have / used to have an industrial bearing supply store.
  6. R

    Which bearing kits do you guys prefer?

    I went to a bearing supplier.-----Clearly stated that I wanted quality bearings.----Not a kit from the " hueflungdung " distributor.----No need to save $15 / $20 at all.
  7. R

    03 mercury 60hp hard start, blue smoke

    Are you pushing the key in and holding it in while cranking to start it ?
  8. R

    Low compression on Johnson 45hp pull start.

    It should be easy to determine once head is off.----Post picture of top cylinder.
  9. R

    Complete removal of vro components

    I would say ---Yes it can be done.------Will need a 0438559 pump.
  10. R

    Low compression on Johnson 45hp pull start.

    As clearly stated the head can be removed with powerhead in place !
  11. R

    Low compression on Johnson 45hp pull start.

    Pull the head off now.-----The head can be removed with powerhead left in place.----The head is warped and needs to be resurfaced before new gasket is installed.---
  12. R

    Low compression on Johnson 45hp pull start.

    Remove cylinder head.----Inspect cylinder.----Lucky you if it is just a blown head gasket.-----Model # of your motor?
  13. R

    Force 120

    Perhaps the motor is running on 3 of 4 cylinders.----Test compression and test for strong spark.
  14. R

    2001 175 Ocean pro Low Rpms and bogging down .

    How did it run for you last season ?----My advice is always the same , start with a compression test.----If you have to use the primer valve it points to a fuel issue.-----The primer valve ( wrongly called a choke ) injects fuel directly into the airstream.----This fuel bypasses the metering...
  15. R

    Outboard top cylinder getting hot

    You will need a puller ( 3 bolts ) to take off the flywheel.----And a 12 point 5/16" thin wall socket for the rod bolts.
  16. R

    No oil pressure after changing engine oil ?

    Something is wrong with your oil pump or pick up tube.----Or the gauge is not working.
  17. R

    No spark

    Remove flywheel.----Remove distributor cap.----Remove rotor.----Inspect anti reversing spring.----Clean all part and reassemble.----Inspect wee boots on distributor cap.-----Note , the wires are screwed into the distributor cap.----Did you take note of post #5 or disregarded that bit ???
  18. R

    Evinrude 4hp 2 cylinder 2 stroke cooling question

    If water is spitting out with exhaust relief you are OK.-----You installed a new impeller.----An inspection of the impeller is due 5 years from now.
  19. R

    Outboard top cylinder getting hot

    ???----Those left the factory with 150 PSI or even a little more.----Time to tear it down for at least 1 O/S piston / rings.-----As per post #4 it was not your lucky day.----Bottom cylinder also suffered !!-----Make it 2 new pistons.----In my opinion it is worth fixing if you do the work...
  20. R

    Mercury 1968 200 20hp prop

    Your location ?----And what pitch prop are you looking for ?
Top