Search results

  1. alldodge

    towing capacity question

    My boat weights about 1K less dry then yours and I use a 3/4 with class 5 hitch. No issues
  2. alldodge

    5.0GL-C won’t get on plane

    Maybe use jumpers and hot wire the pump directly. If it runs and fills the filter/carb then would be another issue
  3. alldodge

    5.0GL-C won’t get on plane

    Does the pump run when motor is cranking? If not, is fuse blown?
  4. alldodge

    Quicksilver 3000 throttle control button install

    Each can be different, I wouldn't know without looking at it my self. Look at the opening and see if there is something that may show which way
  5. alldodge

    Quicksilver 3000 throttle control button install

    Move forward without touching the throttle only button. It should be able to be removed
  6. alldodge

    Automatic trim tabs

    Auto tabs are great when they work, but I've replaced 6 units so far. I would just get tabs and forget about the auto
  7. alldodge

    TWIN 1994 VOLVO PENTA 8.2 OVERHEATING

    More info??? Brand new installs and is boat in the water or on a hose? Hose connections going to pumps are correctly? Post some pics of the setup
  8. alldodge

    77 Carver 2866 Santa Cruz wiring help

    These are basics
  9. alldodge

    1993 5.7gi wiring diagram

    Shows its GM Being a 93 it might be close to this one
  10. alldodge

    1993 5.7gi wiring diagram

    Sounds like you need a GL instead of Gi and if its a GL then which one
  11. alldodge

    5.0GL-C won’t get on plane

    Using an advance timing light or having the damper marked so advance can be seen. Set base timing at 10* then remove shunt and verify 5.0GL-B/C/D/E Models1 Engine RPM. . . . . . . . . . . . . . . . . . . 89 AKI Fuel Initial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10°...
  12. alldodge

    77 Carver 2866 Santa Cruz wiring help

    Being that old it's not likely you can find the diagram unless Carver has it. Most likely you would just wire using the boating industry standards. Don't know if you have a Gen, but without one of those run house Bat wiring, into cabin and use buss bars then go to fuse/breaker panels
  13. alldodge

    1993 5.7gi wiring diagram

    Serial or complete model number, like 5.7 Gi (something like A, C, J, JH, etc) There isn't much on VP This is the only one I have and its hard to read
  14. alldodge

    Mercruiser Oil Pressure Alarm switch troubleshooting

    The alarm switches are designed as designed for carb motors. Key ON alarm, start alarm OFF Page 4E-2 is for a MCM which means sterndrive (note the shift interruptor), MIE is inboard. It list only 5.7 but this would also include 5.0 Both are Tee'd together, the pressure sender is the larger...
  15. alldodge

    Merc cruiser 5 0 backfire

    Agree to disagree All good
  16. alldodge

    ECM Swap ? Plug and play ???

    No reflashing a 555
  17. alldodge

    Trim / Tilt

    The hydraulic trim has check valves inside which upon impact will open some and allow drive to lift. That said if the impact is hard enough its just going to break something.
  18. alldodge

    ECM Swap ? Plug and play ???

    From my looking around its my "opinion" this will do nothing to give you more power, or maybe noticeable power. Your original ECM 3885461 is NLA and not finding the replacement just looking at your motor In other discussions finding 3885461, 3885465 is replaced by 3889007 When a boat...
  19. alldodge

    Mercruiser 6.2L Coolant Loss

    Could even say way does Merc put plastic plugs on the closed AF side. Should just have brass plugs.
  20. alldodge

    Mercruiser 6.2L Coolant Loss

    Yes, sort of. The chart shows there is an issue but does not show how much. The plugs screw into Bronze/Brass fittings. The Brass is screwed into cast iron, so we have Brass to Cast already and were discussing the Brass to Stainless. This chart shows more of the degree of an issue using...
Top