Search results

  1. alldodge

    Overheating motor

    With large amounts of air, I'm thinking a blown head gasket. I would do compression test first because its easy. If compression checks out even on all cylinders and no wet plugs, then look at the drive pump housing and impeller
  2. alldodge

    Erratic Alarm not starting 2017 60HP 4 Stroke EFI

    If your not getting the long beep then there would be no code. A dealer G3 scanner should be able to look for past codes, but a Rinda would not be able to. Here is the warning beeps for the EFI
  3. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    Yes, so it can be put on a stand and connected to the dyno If ECM things the motor is not in-gear it will limit RPM. That said, if this did happen there would be an alarm. So if you get beeps when key is turn to RUN then this would not be the issue Don't recognize NOC I haven't put my...
  4. alldodge

    What prop do I use on a regal lsr 1800 dti Deisel

    Off hand wouldn't know. If you tell us are you getting less, more and max listed WOT RPM? What pitch is on it now? What speed at WOT?
  5. alldodge

    Adjusting the idle-2008 Mercruiser 3.0

    Over many years when the throttle handle gets old the grease inside the control needs to be redone. When this happens using throttle only in the forward direction has enough friction to move the shift cable also. A method to get around it is go throttle only but go to the reverse side. Going...
  6. alldodge

    Mercrusier 350 MAG MPI - RPM issue under a load

    Would there happen to be a dyno shop nearby?
  7. alldodge

    Carburetor Issues, Dripping Carbs...

    Things get bounced around in shipping
  8. alldodge

    3.0GS MBYMCE Exhaust manifold leak

    Shouldn't have any more rust on the exhaust ports then the intake. What's the gap difference between intake and exhaust? Carpenters framing square or other straight edge
  9. alldodge

    3.0GS MBYMCE Exhaust manifold leak

    Yours may not be alone, but having not heard another case similar to same issue, and not knowing exactly where the crack is, I'm thinking the man is put in a bind. If the head isn't flat within 0.003 then when its fastened there is enough binding/warp transferred to the man. Then the heat cool...
  10. alldodge

    Mercruiser 8.2 w/Cats & Closed Cooling Question

    Looking at the exhaust for a little while I would say most likely. It needs more review but both the old style and new all use the drain tubes Look thru the link and select each serial number series. Then select "raw water port" and "raw water starboard". Looking thru the hose connections...
  11. alldodge

    2004 Volvo Penta 3.0L engine knocking

    A motor knocks when a rod bearing spins of is damaged. In many cases its because the the journal was not machined correctly. I'm working on a Merc Reman 454 that has less then 100 hours. The motor needs to be rebuilt and in most cases (depends on motor hours) it just take the crank to be...
  12. alldodge

    3.0GS MBYMCE Exhaust manifold leak

    Put a straight edge on the head intake/exhaust ports
  13. alldodge

    Perfectly for 15 minutes then, surging, knocking, and jumping tac

    Vac gauge no, would have trouble finding a place to connect it also on a boat motor
  14. alldodge

    Volvo Penta KAD 300 power steering issue

    Please look at the manual. The cap is removed tube attached to bottle and bottle is upside down feeding helm
  15. alldodge

    Volvo Penta KAD 300 power steering issue

    Need to remove the cap and make sure it stays full
  16. alldodge

    IAC problems

    No expert, but pins B and C are listed as switched. This tells me the ECM grounds those pins to energize the coils. Meaning the other pins have full power when ECM is powered up. The test light will flash because ECM is switching on/off which will cause the like to flicker on either side of...
  17. alldodge

    Volvo Penta KAD 300 power steering issue

    The manual shows to connect the bottle with a tube connected to the fill port. This will let air out and keep oil filled. By turning wheel each way and seeing nothing come out, and then the second time and seeing air and then fluid, would tell me there is air being purged somewhere
  18. alldodge

    Fuel supply module

    The code will help but may not say what is actually wrong, we need clues. Need to know what the fuel pressure reading is. If pressure isn't high enough then full power is not achievable. If its to high then it floods the motor
  19. alldodge

    TBI rebuild help needed

    The TB is a GM part. Look up the Reg for Chevy/GMC truck Not saying this is yours, just what to look for https://truckprousa.com/i-6275406-jet-performance-tbi-fuel-pressure-regulator-kit-61510.html
  20. alldodge

    1997 3175 Rogue Radar Arch

    Most of the manufactures don't keep older year models, or they just don't care. Cruisers does ok but not so much for older. Builders like Formula and Cobalt keep stuff around If you can feel/see the hole try to guess at the diameter. Most bolts will be standard and not fine thread. Guess at...
Top