Search results

  1. alldodge

    New to me Colbalt, Overheating only while pulling tube or ski

    No special tools needed, remove the six nuts and pull the drive I only mention to remove the drive because it will make it easier to replace parts with the drive being out. You might be able to replace the part without removing the drive. Raise full up and see if there is room I don't know...
  2. alldodge

    New to me Colbalt, Overheating only while pulling tube or ski

    Can get yo that part after removing drive
  3. alldodge

    Any way to reset an mpi without rinda tool

    Don't know how to do with 555 other then diacom or techmate
  4. alldodge

    3.0L I/O issue after new shifter was installed

    Suggest contacting NV AG office
  5. alldodge

    Any way to reset an mpi without rinda tool

    Depends on what ECM If its MEFI, turn key ON with jumper in service mode, then move throttle to WOT and return. Turn key OFF, codes should clear
  6. alldodge

    New to me Colbalt, Overheating only while pulling tube or ski

    Sucking some air Hey @Scott Danforth what do you think?
  7. alldodge

    New valve cover gaskets and still leaking V6 4.3

    If covers and head edges are straight, might clean the surfaces and use some acetone to make sure all the oil is removed, then use some Black RTV in the corners. Put covers on but don't torque right away, finger tight so the RTV comes out some. Next day torque to spec Hope others will come...
  8. alldodge

    New valve cover gaskets and still leaking V6 4.3

    Those are the new style and should not have much issue sealing. The gaskets fits inside a grove on the cover and it uses 3 bolts in the center Need to use a straight edge and see if the cover edge is straight. Like a framing square. Are they both leaking or just one side? Torque shows 106...
  9. alldodge

    New valve cover gaskets and still leaking V6 4.3

    What 4.3, serial number?
  10. alldodge

    Volvo Penta SX - water leak help

    Transom nuts don't back off on there own, your transom is shrinking
  11. alldodge

    Poor man’s boat - 1988 sea Ray weekender 230

    Use exterior grade plywood and your good
  12. alldodge

    1995 Stingray 4.3L Mercruiser No Start

    Its a Mercruiser, it has a slave solenoid The boats motor wiring is what's above Here is the helm wiring
  13. alldodge

    2016 Mercruiser 4.5l Shift Interrupt switch

    Again need motor serial number
  14. alldodge

    3.0L I/O issue after new shifter was installed

    The shift cable is not adjusted correctly. Most likely the shift interruptor is switching and causing the motor issues
  15. alldodge

    Merc 4.3 in a 2006 Maxum SR3 1800. Will crank, won’t start. Seems to be fuel system related…

    12V direct is of no issue, just connect +/- correctly and it should power up
  16. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Yep, I brought up the thread in 3 windows. Port, Stbd and my comments
  17. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Oh well, just blew that one STBD 13.1 and 12.0 problem child low voltage PORT 12.9 and 11.9 STBD has misfires 1, 2, 8 CAT temp 200* higher Less fuel ms and more degree timing Idle set 600 Port idle set 636 That's all I got, hope @muc might see something
  18. alldodge

    2016 Mercruiser 4.5l Shift Interrupt switch

    What is the motor serial number?
  19. alldodge

    Merc 4.3 in a 2006 Maxum SR3 1800. Will crank, won’t start. Seems to be fuel system related…

    You got the right method and your down to the pump. You did say it was getting 12V, and if it is check the ground. If the ground is good, pull pump and bench test
  20. alldodge

    Old Boater Collections

    Its not folks, edit and remove please use PM's
Top