Search results

  1. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    My heads starting to hurt port 81 - motor is running stbd 78 - motor in not running I'm trying to compare apples only
  2. alldodge

    1995 Stingray 4.3L Mercruiser No Start

    Assume a carb motor Wiring is for a Bravo, if you have an Alpha the interruptor goes between the Dizzy module to Ground
  3. alldodge

    2016 Mercruiser 4.5l Shift Interrupt switch

    Idle Air Control valve. Its what the computer ECM uses to control idle rpm. It can get gummed up or just go bad. Doesn't happen often but can happen. If it goes out completely you have to give it throttle or it will die
  4. alldodge

    2016 Mercruiser 4.5l Shift Interrupt switch

    It could, and it is adjustable Could also be the IAC is starting to stick/fail. Is the idle smooth and at what RPM, and when it doesn't stall does the RPM stay steady?
  5. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Maybe you already posted it, but what does the Port engine show with Diacom connected at the Port engine like you did with Stbd?
  6. alldodge

    2007 Rinker electrical issues

    I think Marina connected something wrong and don't want to admit it, because they don't want to pay to fix. Electronics are sensitive and a split second of reverse wiring, kills things Look real close around the Bats and see if any of the cables or wires have burnt spots on them. Does the...
  7. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    STBD 12.8 and 11.5 PORT 12.9 and 11.9 What is the Diff at the Port Engine?
  8. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    I'm on the other side of that one. Motor running Helm it shows 12.8 system and 11.5 Bat Engine 13.2 Ignition 12.15 Bat
  9. alldodge

    Trim cylinder rebuild - Seized inner pin (closest to transom)

    Rent one from local auto parts store or maybe even home depot
  10. alldodge

    how to lift new 5.7 motor with edelbrock manifold

    Full dressed 502 and two 1 inch lifting straps
  11. alldodge

    Trim cylinder rebuild - Seized inner pin (closest to transom)

    My question is why do you want to try heat First? Try a puller first
  12. alldodge

    HELP, ECM Fail or something else ?

    I'll put it this way, Bob will not steer you wrong and John is one of the best at finding and fixing the faults. As for the others you mentioned, I would only go to them if Bob or John were unavailable and time was the issue
  13. alldodge

    Trim cylinder rebuild - Seized inner pin (closest to transom)

    I don't like high heat around the transom. It has a rubber seal between assy and transom. Then you have the fiberglass and Gel coat
  14. alldodge

    2014 3.0 mpi want go over 2500 rpm’s we have Cleaned all injectors replaced distributor and idles fine just will not go over 2500 like it’s on a rev.

    Use the Diacom and record as the motor runs, then post it
  15. alldodge

    how to lift new 5.7 motor with edelbrock manifold

    Personnel opinion but I don't like carb plate lifts, but that's just me Put hooks on the exhaust sides or front and rear of heads I have the exhaust installed on motor and use 1 inch web straps around both of then and attached in the center above
  16. alldodge

    Ran amazing then shake no thrust

    Should be using manual 15 shows MR43T or RV8C
  17. alldodge

    coversion to electric fuel pump on 1992 7.4 l

    Might go with Carter P4594, its 6-8 psi and states no Reg required Many places list it as Auto but others show its Marine rated
  18. alldodge

    Volvo Penta SX - water leak help

    Looks like the exhaust Y pipe
  19. alldodge

    Trim cylinder rebuild - Seized inner pin (closest to transom)

    Big F Hammer I like ricks method. Tighten it it up and if it doesn't start sliding off, smack the end of the tool with a hammer, not a BFH, regular size. The shock most times makes it break free
  20. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    My understanding is its digital and the reason Merc said i needed a A to D converter
Top