Search results

  1. alldodge

    Prop diameter effect and planing trouble

    ^^ Agree I would not use a 4 blade prop on the boat, it takes more HP to turn and you don't need all the stern lift. Your 4 blade 19 is like a 3 blade 21 Look for a 3 blade 19
  2. alldodge

    Got ME a nice something, BECAUSE!!! :)

    I use ammoseek most often 38 spl shows 0.38 to 0.40 each now
  3. alldodge

    No start situation

    Is carb leaking fuel (dripping) down the throat when its cranking?
  4. alldodge

    No start situation

    Having fuel on plugs, is the new carb flooding?
  5. alldodge

    Filling a termite ridden stringer

    Rip the stringers out and replace
  6. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    Same here I'm still looking for another boat, but no way I want one with any kind of a joy stick
  7. alldodge

    No start situation

    Thanks, you have TKS carb and EST ignition Orange is not a good color for spark (white or Blue) but not ready for a coil yet Don't use starting fluid, it can break things. Take a tea spoon of gas and drip into the carb, see if it will start Need to test the components
  8. alldodge

    Fuel flow

    ^^^ It's a suck and blow thing. Don't want to suck fuel out of the motor and blow it into the fuel tank Look for the arrow
  9. alldodge

    Engine wont shut off with key

    I'm at the point the the motor needs either a complete rewire (everything goes), or need someone that understands how the electrical circuits work and can put their hands on it. We're not getting anywhere. You need to understand why there is a problem having voltage on the I terminal and not...
  10. alldodge

    Engine wont shut off with key

    Today it won't do anything Post 28 it was working
  11. alldodge

    Exhaust bellows

    Special tool, buy or make one
  12. alldodge

    2016 Mercruiser 6.2 ECT - long beep every few minutes???

    All sensors work off a single 5V reference produced by the ECM. Any sensor that draws to much current causes all kinds of issues
  13. alldodge

    2005 bayliner 4.3

    Could fire up the motor with module unplugged and if it stays cool then its the module
  14. alldodge

    2005 bayliner 4.3

    Thats a diode. It may ok but something is drawing to much current. If it cools down after the module is unplugged then its just the module. If it remains hot then might be the temp switch
  15. alldodge

    1997 Glastron 24GS alsrm

    Start the motor, then disconnect one by one the lube bottle, temp switch and oil pressure switch. Temp switch is on thermostat housing has 2 wires on it, gauge has one. Oil pressure switch is low port side next to oil pressure gauge sender. The oil switch is the smaller of the 2
  16. alldodge

    Exhaust bellows

    No it won't sink. On Bravo 3 they only do Tubes instead of bellows
  17. alldodge

    Intermittent Spark

    Sounds like a good idea.
  18. alldodge

    2003 Merc 5.0 MPI no start, intermittent spark

    How about your kill switch? Check for 12V at the coil with key ON and see if it stays there when cranking
  19. alldodge

    Exhaust bellows

    No its not needed. They make a exhaust tube which just connects on the transom side
  20. alldodge

    Electrical Issues after replacing trim switch/sensor 7.4 EFI/MPI

    Don't see a stuck key melting the fuse, but it would cause some issues. The beep garble might just be the beeper having an issue, don't know for sure. The blower might be the wasp or just bad connections, have to look
Top