Search results

  1. Scott Danforth

    Hello all, I want to install a remote oil filter mount for my 4.3 V6, is it neccessary to replace the filter mount bypass valve?

    The reason for the higher 30psi vs 11psi bypass is so the extra pressure drop on the remote lines and filter head don't open the bypass and the oil doesn't get filtered Typical pressure drop across a filter is 4-7 psi. Adding the remote lines, etc adds about 4-5 psi
  2. Scott Danforth

    Hello all, I want to install a remote oil filter mount for my 4.3 V6, is it neccessary to replace the filter mount bypass valve?

    On you motor, just inbolt the threaded block adapter and swap it. As @Scott06 stated, just don't drop in the bilge
  3. Scott Danforth

    Hello all, I want to install a remote oil filter mount for my 4.3 V6, is it neccessary to replace the filter mount bypass valve?

    All the same. I have a twin-filter unit on my big block as I am running a HVHP pump. Transdap filter head and a Canton racing block adapter I also have the local hydraulic company make up my oil lines vs buying the ones in the kit. my home made parts washer used to have a single Transdap...
  4. Scott Danforth

    3.8 OMC replacement motors?

    exact same motor, exact same drive (there were no 3.8's in 1985, only left over 1984's registered as 1985's) I would buy the whole thing for spare parts as the shift cable alone is $950.
  5. Scott Danforth

    Hello all, I want to install a remote oil filter mount for my 4.3 V6, is it neccessary to replace the filter mount bypass valve?

    I would personally feel much better swapping out the 11 psi bypass check for the 30 psi bypass check. if it was my motor, I would swap it.
  6. Scott Danforth

    volvo d6 370 ips overhaul kit

    D6 blocks are common discussions on some of the larger boat forum threads.
  7. Scott Danforth

    volvo d6 370 ips overhaul kit

    use standard pistons and have the machinist use replacement sleeves
  8. Scott Danforth

    1985 Bayliner 2750 Ciera Sunbridge Resto

    yes, however I could buy it from work and spray it at work, so I went with Imron (technically Axalta Coatings). additionally if water gets to the fuel tank in the boat, that means there is over a foot of water in the bilge and it would be sinking.
  9. Scott Danforth

    2018 Parker 2810

    your boat is 28' with an OAL of 35'..... your over 24' in the water
  10. Scott Danforth

    2018 Parker 2810

    and if you have a fishing rod off the stern, they measure that as well.
  11. Scott Danforth

    2018 Parker 2810

    are you looking for water-line length to determine a theoretical speed calculation, or are you looking for the length for dockage fees? because if its dockage fees, they measure for you, and measure from the furthest aft portion of the swim platform to the bow pulpit and they add any anchor or...
  12. Scott Danforth

    volvo d6 370 ips overhaul kit

    Uh....Volvo for Volvo motors
  13. Scott Danforth

    Sea Ray engine replacement

    Summit Racing, NAPA, anywhere that sells Felpro gaskets
  14. Scott Danforth

    1985 Bayliner 2750 Ciera Sunbridge Resto

    It may have been tough as nails prior to the company changing formulation in 2008. Today I wouldnt use POR 15 on anything as there have been too many applications that have failed amongst the car blogs globally in the past decade. I personally have had it fail on multiple occasions over the...
  15. Scott Danforth

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I painted my fuel tank with Dupont Imron snow white. wasnt too bad for cost. the primer cost more than the paint. access and storage is always a good thing. I added PFD storage under the risers by simply cutting an access hole and gel coating the interior, as well as line storage under the...
  16. Scott Danforth

    Can you change from welded to bolted?

    depends on manufacturer pick 20 galvanized trailer manufactures and you have 20 different design and manufacturing philosophies, however all will last the 2-3 year warranty against rust-out. C Channel is easier to use (forming, etc) and to get full coverage on galvanizing. tube is slightly...
  17. Scott Danforth

    Happiest Day of Ownership !!!

    * * * This web site is for documentation and entertainment purposes only * * *
  18. Scott Danforth

    1976 Chrysler 10hp throttle bushing

    make one out of delrin.
  19. Scott Danforth

    '75 24'5" Slickcraft Cabin Crusier

    the paperwork should tell you what you have. (Title/registration/Bill of Sale) in most cases, without paperwork, you have a yard planter the engine is obsolete. the drive is most likely a stringer drive being its OMC which stands for "Obsolete Marine Company" for the past few decades. on...
  20. Scott Danforth

    Can you change from welded to bolted?

    The OP hasn't been back. I own a welder and have access to hundreds more..... I could weld that in my sleep. However there are 2 things in the world where proper penetration is paramount...... Welding is the first one I agree that the trailer can be redone. The cross members are toast. Most...
View older results
Top