Search results

  1. R

    Uppercase on 235 stringer locked up..

    Ball gear wear quickly if the input shaft on upper box is loose.
  2. R

    1961 Johnson Seahorse 40hp Controls?

    The simplex would work too.
  3. R

    Aluminum Transom repair/replacement

    Rivet on a new sheet on the inside if you can get at it.-----Or the outside can be done as well.
  4. R

    Uppercase on 235 stringer locked up..

    Yes there is lots of shimming involved with these gear boxes.-----Google and E-bay may help you find parts.----May help find a shop still interested in working on them or the parts.
  5. R

    Yamaha 50TLRD revs and bogs revs and bogs...

    If you covered # 3 carburetor and nothing changed that certainly says something.------Find out why.-----Motor should behave the same with all 3 carburetors.----Should slow down ( too much fuel ) like it did covering #2 carburetor.
  6. R

    Old Honda 7.5HP (BF75) fuel line - buy NoS or replace connector?

    Install the fittings of an Evinrude motor.------Used on motors from 1960 up until recently.-----Readily available.
  7. R

    What next? 90 hp Mariner

    Cheap to replace pump diaphragm.-----Test operation of the enrichment solenoid valve.
  8. R

    No pee Johnson outboard

    With the impeller installed it will be harder to turn the shaft.----So get the factory impeller.----Never an issue with those.----The tube must be put into the exhaust housing first.--------Then you install the lower unit.------Making sure the tube goes into the pump.----Easy , nothing to it.
  9. R

    Outboard for 26 ft bayliner

    On a 26' boat you might want to look for a 20 HP / remote / electric start / power trim / tilt / bracket ( electric ) to raise and lower it with a push of a button.-------Post picture of transom area.-----How are you planning to operate a motor hanging over the back of a 26' boat ?
  10. R

    Mariner Magnum 40HP - Starting Issue

    Good luck with your motor.
  11. R

    64 Johnson 9.5 “Turtle Motor”

    Are the 2 notches in the brass connecter lined up with the holes for the bolts ?----Is the shift adjusted correctly at the top near / in front of the carburetor ?
  12. R

    Yamaha 50TLRD revs and bogs revs and bogs...

    Use a timing light.----One cylinder at a time.----See if you are loosing spark on one.
  13. R

    Is it worth replacing my transom here? (I have NEVER done fiber glass repair)

    Based on what the pictures show.------If I was fixing that myself it would be about $150 for epoxy and $100 for quality plywood and fiberglass.
  14. R

    Yamaha 50TLRD revs and bogs revs and bogs...

    Test run with another tank and hose.
  15. R

    Mariner Magnum 40HP - Starting Issue

    Throttle needs to be opened a bit.----Full throttle open is not needed and it is bad for a 2 stroke to rev wide open in neutral !
  16. R

    Mariner Magnum 40HP - Starting Issue

    It should start in just a few seconds.-------If you have to crank for 10 seconds then there is something wrong !!
  17. R

    Nissan 2002/2003 70hp TLDI has been stored 3 years - what should I do for sure before startup?

    Sorry-----No need to mix gas and oil on that motor.----But make sure oil injection is working properly.-----Perhaps pay the local boat shop to verify that this motor is ready for service.
  18. R

    Mariner Magnum 40HP - Starting Issue

    Fuel in a carburetor bowl is only at atmospheric pressure no more.
  19. R

    98 Johnson 2 stroke ignition

    Find ----mastertechmarine----website.----Find wiring diagrams.-----Find control box wiring diagram.----Only up to 1995 they say.----Wiring colors are similar I think.------What control box do you have.-----What connecters do you have.----Pictures will help you get some answers.----No idea here...
  20. R

    What year 85 HP Johnson

    That box has the relays for a 2 wire tilt / trim motor.---Possibly trim gauge wires.-----Does nothing else.
Top