Search results

  1. Scott Danforth

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    not sure which mechanism you have however the holes may have slots. additionally, the clearance holes are 5/16" and the t-nuts should be 1/4" that will give a bit of slop.
  2. Scott Danforth

    Filling coolant reservoir 3.0 TKS?

    No, it should be full to the bottom of the lip. You have an air pocket in there Looks line you are about a half pint down
  3. Scott Danforth

    Hull issue on powerquest

    I would look at it sooner than later
  4. Scott Danforth

    Prop shaft question

    I wouldnt.. The great Don S called it always sieze In fresh water, you may get away with it. In salt water, it promotes corrosion
  5. Scott Danforth

    gas prices

    Fuel is the cheapest part of boating
  6. Scott Danforth

    Mercruiser 3.0 water by-pass theory

    Replace the impeller, never worth it to not do it. Overheating is lack of flow
  7. Scott Danforth

    Fuel pump “over spraying?”

    I would be looking at sticking injectors. Have them cleaned and flow tested
  8. Scott Danforth

    Are the blocks of foam in the corners above deck necessary?

    remember, the factory tested the boat by intentionally sinking it. from that test, they determined the amount of foam needed to keep the boat at the surface.
  9. Scott Danforth

    volvo penta Runs and drives but once it reaches operating, it shuts down.

    Its almost never the coil
  10. Scott Danforth

    Are the blocks of foam in the corners above deck necessary?

    The foam is there for flotation to keep the boat at the surface should you forget the plug, get swamped, etc. Without the foam, the boat goes to the bottom with a breach. I would keep/replace the flotation foam
  11. Scott Danforth

    High Prices of used boats and the future? Bubble or not?

    We are going to see a market correction shortly. similar to the 2005-2007 price correction that happened in 2008-2010. may not be as drastic, however there will be a slight correction. RV market prices have started falling. When the lots were empty, RV dealers were charging higher prices...
  12. Scott Danforth

    Anybody Experienced with ClicSeal Pour Spout

    I wouldnt take months. you should be fine for a few week period of time.
  13. Scott Danforth

    Turning Vintage and going Chrome

    Few months back, trying to get in with the Doc.... Me "Doc, almost 54, need to run panels and labs to look for markers for X, Y, & Z as it may run in the family" Also need a specialist to look at my shoulder. Me" Doc, also, need a referral to an allergist as something is kicking my butt...
  14. Scott Danforth

    Gimbal bearing.

    Because comparison sites like Consumer Reports / JD Powers, etc gives products negative values for maintenance points and the marketing department is trying to push sales........ lower quality competitors are doing it and getting better comparison scores on maintenance for less points to touch...
  15. Scott Danforth

    HELP - trying to drive in inner bearing race... NEED TRICKS

    UFP uses off-sized bearings to be "Unique". my local trailer parts place keeps both races on the shelf
  16. Scott Danforth

    Filling coolant reservoir 3.0 TKS?

    take a sample of the coolant in a clear container to look. cant see thru the opaque white tank
  17. Scott Danforth

    lubricate impeller with what? Volvo 3L

    Windex also works. however coming down the aisle at the store with 2 gallons of motor oil, 3 quarts of gear lube and a bottle of KY raises eyebrows told the clerk it was a party
  18. Scott Danforth

    Anybody Experienced with ClicSeal Pour Spout

    I would try to condense all you gel work within a very short period of time
  19. Scott Danforth

    Small crack in fiberglass hull with stains

    those brown streaks are the tannins in the wood leaching out as the wood structure rots you can cosmetically fix it, however I agree with Ted, there is an underlying issue that should be addressed first
  20. Scott Danforth

    Best manuals

    only place to get mercruiser manuals is from Brunswick directly. https://publications.brunswick.com/ you can buy used ones on ebay.
Top