Search results

  1. alldodge

    Bravo 3 bell housing removal. (lube leak)

    Parts are items 1 thru 5 https://www.mercruiserparts.com/bam/subassembly/30966/952/180
  2. alldodge

    Mercrusier 5.0 MPI (2008) RPM stops @ 3200.

    First post list replacing cap and rotor Guess we should have made sure you did that :unsure:
  3. alldodge

    Merc 5.7 Carb Help

    Hey Bondo Maybe he buys a rebuilt one for 350 and installs it for 250 :ROFLMAO:
  4. alldodge

    Merc 5.7 Carb Help

    One of my boats is a 95 Rinker with the Weber carb and it still runs fine. Did adjust the choke some years ago, but otherwise it has not been touched
  5. alldodge

    Continues running fuel pump

    High or low should not matter, what does matter is the amount of pressure the pump puts out
  6. alldodge

    DPS-A trim cylinder rebuild needed?

    The manifold is behind the drive. Takes very little to remove drive and get it out of your way
  7. alldodge

    4.3 tb IV no fire from coil

  8. alldodge

    Bravo 3 Shift Adjustment . . .

    Not bad for 24 and salt water
  9. alldodge

    Continues running fuel pump

    BTW, that's a standard relay "automotive" type. Could take it to the local auto parts store and get one
  10. alldodge

    Continues running fuel pump

    With tapping on the relay and it stopped then I would agree its the relay Tx for the SN
  11. alldodge

    Bell housing to outdrive gasket protruding

    OK no RTV, yet the bead came out. It should not have happened, there 2 flat surfaces. The red bead is what helps it stay in place. Guess I've been lucky, but never had one slide out
  12. alldodge

    Starter wiring please help

    There is a Yellow/Red wire from the key switch to the relay on the motor. When the key is turned to start the relay energizes which then supplys power to the starter thru another Yel/Red wire Since it worked before, I would guess one of the connections is bad between the starter and relay. It...
  13. alldodge

    Bell housing to outdrive gasket protruding

    The gasket should not slide out. In most cases this happens when folks use RTV. The RTV makes it slick and it slides out. The gasket should be installed dry
  14. alldodge

    Merc 5.7 Carb Help

    With it only having trouble when cold, that would mean it just needs a choke adjustment. When motor is cold, pump the throttle one time and look to see if the choke plate has closed. The choke is adjusted by the rod attched from the pot mounted on the intake. If the pot has gone bad it can be...
  15. alldodge

    electric fuel pump problems

    Don't know which one is which, but the MPR has to energize to supply power to others. It should be like this, but note this is for a Mercruiser but it should be the same just maybe different pins numbers
  16. alldodge

    electric fuel pump problems

    The MPR should have 12V on one side full time. If it does not, then its a fuse, a bad connection or broken wire. The relays can be swapped with each other
  17. alldodge

    2008 Tahoe Q4 3.0 Mercrusier

    Flipping it ON doesn't mean its passing voltage Power comes from the key to the purple wire. The purple wire goes to the kill switch then to the gauges and the motor. If the switch or the wire breaks connection, the gauges do not turn ON nor does the motor Use a voltmeter and see if you have...
  18. alldodge

    Bravo 3 Shift Adjustment . . .

    (y):cool:
  19. alldodge

    Bilge pump runs does not pump

    Try this, disconnect the hose from the outlet Place the hose down lower and turn the pump ON If the pump flow is good, slowly raise the hose until it stops
  20. alldodge

    Continues running fuel pump

    In most cases is one of the diodes which have shorted out. Do you have the serial number for the motor?
Top