Search results

  1. R

    1986 90HP Crossflow Johnson - RPMs increase at WOT when steering

    Lower the engine as needed and test run.
  2. R

    71 Johnson 50 50ESL71S clicking when going into reverse

    No damage done with the wrong oil.-----The oil pressure does the shifting.----Reverse requires the highest oil pressure to compress the spring on the clutch dog.-----So this machine has a strainer screen in front of the oil pump.----This screen has been known to disintegrate.---Possible damage...
  3. R

    1975 115 2-stroke inline 6 WOT problems

    If motor keeps running with the manual fuel pump you need to go over the entire fuel system.----Starting with screen in the fuel tank.
  4. R

    Safe to tow with bow not resting on front roller?

    In a high speed collision situation stuff will break.-----On my project the bow eye was anchored with a small block of wood.----That wood was rotten and come out as powder.------Replaced with solid glass with a second bow eye to boot.
  5. R

    Omc identification

    Time for a full tear down and inspection I say.
  6. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    Yes that is what you are looking at.-----Properly done your grandkids will be running this motor.----These motors are scoffed at by some.----But seeing it was running with that kind of damage means that these engines are well built with just one flaw.----That being the design of the top piston ring.
  7. R

    Omc identification

    Cable disconnects up at the top / rear of the motor.----Post picture of cracked area.----Recommend inspection for rust damage if water was in there and exposed to oxygen !!
  8. R

    1975 115 2-stroke inline 6 WOT problems

    The bulb does not stay hard once motor is running, very normal.
  9. R

    Omc identification

    That would be the 400 model.-----Careful with that cable.
  10. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    No point going any further.---Classic broken rings syndrome.-----Motor needs to come apart to replace with o/s pistons.---4 of them.
  11. R

    79 Merc 70hp Problems

    ???----Is that the date you signed on to this forum ?
  12. R

    Safe to tow with bow not resting on front roller?

    Is that a simple---S hook ----on the safety chain ?----If so that is the first thing to replace with something bigger and better for a 20' boat.
  13. R

    Omc identification

    It be a 78 or newer.-----Not electric shift.-----Smaller ones were " 400 " models with gearcase similar to V-4 outboards.-----Larger ones were the " 800 " models with gearcase similar to a V-6 outboard.----So what HP or engine is in the boat ?
  14. R

    What is this switch for?

    As shown in your picture is the for normal operation.
  15. R

    What is this switch for?

    The unit is the primer valve.----It is NOT a pump.-----When you push the key in WHILE cranking the motor this valve opens.-----Fuel is then sprayed directly into the motor for starting.------It works better than choke flappers.----The red lever is for manually opening the valve.----In case you...
  16. R

    1998 Lowe 245 with 225 HP Evinrude Fitch motor

    model # of the 98 model 225 Ficht ?
  17. R

    Safe to tow with bow not resting on front roller?

    You should be able to pull it up to the roller right in your driveway !
  18. R

    Motor swap help

    There is an adapter cable available.---Contact your local friendly BRP shop.
  19. R

    1969 Merc 650 - Shifting problems

    Sorry ----These things slide together.-----I was not there to see what you did that may have damaged it.
  20. R

    Cylinder not running

    Install new powerpack.-----That may fix it.
View older results
Top