Search results

  1. R

    NO START AFTER LOWER UNIT REPLACEMENT

    No you can not run it that way.----This is suggested simply to assist you in trouble shooting.
  2. R

    6hp 6rl75r

    Find someone at the ------aomci-----Post a wanted ad.-----Many members have a stash of good parts.----These motors were made the same for about 20 years.-----Lots of them around in my area.
  3. R

    1986 90hp Mercury IL6 dies when put into gear

    Fact-----When you have it idling real smooth and sounding fantastic it is often too lean.------So the no $$$ spent thing is to open all 3 low speed mixture needles 1/8th turn and test run at the lake.---If it still stumbles open another 1/8th turn.----May not idle as smooth but that is the way...
  4. R

    primer solenoid leaking

    A simple repair kit likely would have fixed the original one.----There is not much that goes wrong with these reliable primer valves.---Same unit for about 30 years.
  5. R

    6hp 6rl75r

    Your location ?------If in Canada-------evinrudeparts.ca-----May offer help.
  6. R

    1984 E185TLCRS Won't Rev Past 3000 rpms

    The neutral safety switch only prevents the starter motor from cranking if the motor is in gear.-----The neutral safety switch has nothing to to with being a rev limiter.-----Shift interrupt switch in not installed on your motor either.-----You need a manual and need to do some simple trouble...
  7. R

    Johnson 4R71D Resurrection Attempt

    Just take the head off with the block in position.-----It will come off.----Then report on the condition of cylinders.
  8. R

    1984 E185TLCRS Won't Rev Past 3000 rpms

    Facts------There is no S.L.O.W. mode on a 1984 model !----Post your compression numbers that you have today.----Then check for spark.-----It must jump a gap of 3/8" or more on each lead.-----Are the 6 high speed jets in the carburetor bowls confirmed to be clean, yes , no or no idea where they...
  9. R

    NO START AFTER LOWER UNIT REPLACEMENT

    No the splines and count are not different !!----The issue is changes made in length of splines and depth of the hole in the crankshaft !----Back all the bolts out 2 turns and tell me what happened.-----Sorry , I am not there to help you and point all this out.----I discovered this issue years ago !
  10. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    Double that estimate.----Time taken from removal of first bolt to turning the key to start it.----And likely more.------You need to go over carburetors.----Starter motor.----Fuel pump.-----Cylinder head covers.
  11. R

    1963 Johnson QD-24B

    As clearly stated the friction on the wee spring link pulls the pawl into position.----So check that.----If pawl is new , make sure it is not binding on the pin.
  12. R

    Top piston worth replacing? (120hp low compression)

    RTV is not to be used where there is gasoline present.----Simple as that.----Put a lump of cured RTV in some gasoline and see what happens.
  13. R

    NO START AFTER LOWER UNIT REPLACEMENT

    There were changes made in the area of the splines on the crankshaft.----And yes when you install the lower unit of a newer motor there will be a problem.----So if you back off the lower unit bolts 2 turns the motor turns easily by hand ( sparkplugs out ) and it jams when you tighten the screws ?
  14. R

    1963 Johnson QD-24B

    Perhaps explain in more detail what the issue is.-----Recoil spring not retracting the pulley ??----Or pawl not engaging the flywheel to start motor.----We are not looking over your shoulder.---Explain stuff.------I rebuilt a 1963 10 HP a few years ago for the 8 year old grandson.----He started...
  15. R

    1963 Johnson QD-24B

    Agreed----No lube on the spring and in the groove.
  16. R

    1960 Merc 400 shift shaft trouble

    Fact-----These things are easy.-----You must understand that the clutch dog is spring loaded.-----When you take it off in neutral it usually goes into forward when you bump the lower unit.------So.----Make sure the lower unit is in neutral as you slide it up.----Or make sure control is in...
  17. R

    Can't get boat even on bunked trailer.

    I put the rear roller in the water.-----Start pulling the boat on the trailer.----If effort gets to much I back trailer in 5 or 6 feet.----Repeat as needed.----Put my 30 ' Scarab Sport on the trailer with no help.----Folks sometimes offer help , but I say " no thanks " and boat always sits...
  18. R

    1996 Evinrude E88TSLEDR - Overheat - Starboard Side Not Flowing Well

    You have to be really careful with internet presenters.----One was trying to take a V-4 apart and was hammering taper pins in the wrong direction.----Then on another video he was trying it on a V-6.------I learned about these broken rings back in about 1980 and I can rebuild one without looking...
  19. R

    Omc identification

    ??----It appears to me that this crack is due to water in the gearcase or a passage way..----It froze and cracked the case.----Pressure test this gearcase.-----If it fails you need to take it apart for inspection.-----I assume you just bought this boat.
  20. R

    1975 115 2-stroke inline 6 WOT problems

    I remember people complaining about filters on outboards looking empty 50 years ago.---Motors ran just fine.-----Just the way it is I think.
Top