Search results

  1. alldodge

    MX 6.2L MPI Horizon MIE: Rebuild Recommendations Needed

    You should either have one of these, left or right side of pic
  2. alldodge

    A Frame hoist

    There is a guy on OSO selling a A Frame hoist 20x20 in clearwater FL. I'd buy it but its to far away Hey Scott Danforth he's in your area https://www.offshoreonly.com/forums/swap-shop/362723-10-ton-20-wide-20-tall-frame.html
  3. alldodge

    2010 Tahoe Q5i 4.3L Mercruiser Carb. No power to ignition switch.

    You need a voltmeter. A test light will light with much less then 12V, it is a good tracer though. Follow the wiring in the diagram. You should see voltage on both sides of the 50 amp breaker and at ignition
  4. alldodge

    Upper Hlinge Pin Bushing Wear

    Are the stainless ground cables installed? How are the anodes
  5. alldodge

    Upper Hlinge Pin Bushing Wear

    The pin does not look like a Bravo/Alpha, not enough teeth
  6. alldodge

    Three battery on a two way switch

    Don't connect series, that makes the output 24V and things will burn up The house would be parallel (treated as one bat) and the start would be by its self. Suggest using an ACR to charge all bats once motor is running. It will do it automatically but still may need a onboard bat charger for...
  7. alldodge

    97 5.7 LX, A 2 GEN 2 drive questions

    Use 2 screw drivers to remove seal The drive needs to be pressured tested to find leaks. There is a sticky in the Adults Only section on how to The bellows are old and since your going this far I would replace them
  8. alldodge

    Any Windlass suggestions for 1995 Larson Escapade 240 Day Cruiser

    This is one like yours which shows a vertical type. Things you need to look for is space available for the anchor motor and rode. The above deck (Horizontal) requires less room/space needed below deck, but not by a lot. Then need cabling, breakers and control panel. I would suggest Maxwell...
  9. alldodge

    2000 5.7 psi pwtr no fuel to injectors

    Don't know which distributor you have but if its the EST then here is how its tested Have not heard the method of measuring resistance in both directions to determine if its good. This would be acceptable if there was a diode inline, but the distributor does not use one of those that I'm...
  10. alldodge

    Alpha one gen 2 Gimbal housing gasket seal

    The one removed from my Formula during transom work was still pliable but would not spring back to full size, but also was not leaking
  11. alldodge

    Where To Find Riser Fittings....

    If its 1 inch ID then you have the right size, the older thermostat housing did use larger hoses Did some research and the new ones being sold by Merc look just like the ones you have. The original had more copper in them and the part number was 22-866725
  12. alldodge

    Winterizing with 4.3 Merc

    If that is all you did then :nono: Would be good to know what 4.3, maybe a year Need to drain the block, lower circulating water pump hose remove and lower hose come from the Alpha drive and lower to bilge to drain water out Check the outdrive drain holes
  13. alldodge

    Timing issue;1998 Mercruiser 3.0 liter 4 cylinder

    Motor should be warmed up Connect the jumper at the distributor and jump the interrupter switch wires together. If motor dies timing is probably to far out
  14. alldodge

    Mercruiser 3.0 in colder weather

    Sounds like you got it, only thing in the manual it discusses probing the drive holes, and crank the motor (without starting) slightly to clear water from pump
  15. alldodge

    Mercathode - Worth it?

    Should probably use Aluminum
  16. alldodge

    Mercathode System removed. How to I tell if it works?

    It is tested by having the boat in the water for at least 24 hours, and plugged into shore power. Need a platinum coated wire probe and it gets connected to a good multimeter. Meter is placed on millivolts and probe placed in the water behind the drive. The negative on the meter is connected...
  17. alldodge

    Engine jobs

  18. alldodge

    ENGINE Stalling

    Not sure which year or serial number your motor is, but there should be a connector on the shift plate which connects to the interrupter.
  19. alldodge

    Transfer case motor

    2008 Ram 2500 and the service 4WD light comes on every now and then for the past week or so. Been busy so didn't get to it until today. Thinking it may be a bad connection, removed the connector and all good. Read up on the issue and most lead back to the transfer case motor. So I'm putting...
  20. alldodge

    1998 Mercruiser 5.7 Engine alignment problems

    I'm thinking rear engine mount needs replacing and/or the transom assembly has been twisted Have you tried loosing the front mounts, use a hoist to lift the motor just a tad off the bottom nut from the thermostat housing, then adjust the bottom nuts up until they just touch the bottom of the...
View older results
Top