Search results

  1. alldodge

    Need Help w. My General Electrical Setup

    I see you having this configuration now
  2. alldodge

    Need Help w. My General Electrical Setup

    First all grounds go to ground, including the house and two starter bats, otherwise you need an onboard charger just to charge the Inverter (house) bat. Lets call your bats as follows, 1) Start 2) House 3) Inverter, this way we can keep things straight. The normal configuration for batteries...
  3. alldodge

    ESA testing/wiring help please.

    Howdy I'm finding the 2.9 motor was installed in Rangers and Broncos from 86 to 92. The motor was never installed in a boat and this is the issue. ESA module needs to be connected to the distributer to cause the motor to miss. This is the wiring for the OMC V8 The wiring for the 2.9L V6 is...
  4. alldodge

    Bennett Trim Repair And Auto Pro Install

    Taped the control template in position. Think this would work better using something clear (in my case) or even wax paper. This way I could see in reference to the holes already their. If I do this again, might try something like that. Then cut the center piece out using a hack saw blade...
  5. alldodge

    Bennett Trim Repair And Auto Pro Install

    Well alrighty then :) Removed the end caps (hinges) off both and was going to install new ones and the instructions did not say which of the rods to use, only that the pointy end goes to the bottom. Kit comes with 4 rods, 2 short and 2 a bit longer. Called Bennett and I need to use the long...
  6. alldodge

    Bennett Trim Repair And Auto Pro Install

    The parts came in, and the senders come with 2 sets of rods. The directions indicate to install with point end into the cylinder but does not say which to use. I'm going to assume it will be ones which will not interfere with screwing the hinge on. Will also need to drill a 5/16 hole for the...
  7. alldodge

    Bennett Trim Repair And Auto Pro Install

    Tracking says the trim items are coming in today. Removed the panel and switches today to get ready for it. Since my drive trim gauges doesn't work (digital trim) I either need to replace with something else, or maybe install a different gauge
  8. alldodge

    Outdrive/Engine Stand Adapter

    Not a bad thought but going to be hard to move. This is my engine stand that also used to rebuild the drive
  9. alldodge

    2008 Mercruiser 4.3 L/H alpha not starting and backfiring out the carberator.

    Disconnect the wires going to the shift interrupter, see if bad idle stops Assuming timing is set at 10 BTDC with White/Purple wire grounded for base timing mode Firing order 1-6-5-4-3-2 distributer rotation clockwise looking down on top of it If all that checks out, suggest compression test
  10. alldodge

    Wiring diagram

    Been a whole lot of folks ask same question on many different types and the answers have been pretty much the same; Its doubtful to find one by a manufacture for the boat, even boat is different. What does stay the same is the wiring for the motor an controls. So look for wiring for which...
  11. alldodge

    Draining power steering oil cooler

    You should have one like in the pic below, if that's the case there is no drain plug and its self draining
  12. alldodge

    Bennett Trim Repair And Auto Pro Install

    Just need to get some things out of the way and I can squeeze in, mainly exhaust riser and lube bottle/bracket. Doing that will allow me to finish to secure the two wires hanging from the oil temp install this summer
  13. alldodge

    Bennett Trim Repair And Auto Pro Install

    Thanks Tom Disconnected the starboard side line and fitting, good think my arms are that long. Think I'm going to have to remove the exhaust again to get to the trim tab pump, either that of figure out a way to make my arms 2 foot longer. :( Removed the screws and just twisted the cylinder two...
  14. alldodge

    Stamas Trim Activation Question

    Probably you have a bad trim limit switch (port side gimbal ring). The trim limit switch makes a connection when the drive is low, to get it up higher the two buttons are used to bypass the limit switch. Note the Blue and Purple wire feeding the switch. Find these wires back by the drive, and...
  15. alldodge

    new to me boat, shower drain question

    Shower bilges are turn ON/OFF with a float switch. Need to see if power is going to the pump and float. Normally 12V runs to the float switch then to the pump. The same thing would happen if the float switch controlled the ground. Hard to tell clearly, but dose look like 12V (Brown wire) is...
  16. alldodge

    2002 496 Mag HO - IAC location

    Its on the intake manifold and looks like item 38 in link, follow the hose from the throttle body to the IAC http://www.mercruiserparts.com/bam/subassembly/31823/6708/70
  17. alldodge

    BBC build- Don't tell the Admiral

    You sure this is the same one you where looking at, found at first? It's max flow rate is only 7-9 GPM. It says its is used for small diesel motors like in forklifts, tractors and such
  18. alldodge

    2000 Mercruiser 5.0L Power Steering Leak

    I would say its in one of these two locations and more then likely its the pump shaft seal. Take a paper towel and place between the pulley and front housing. Place another towel taped lightly to the bottom side of the pump housing
  19. alldodge

    5.7L with 1.62 gears, looking for advice

    Yep, that makes a difference, it is either 2.0 or 1.62 Need to rotate and count or count the lower gears
  20. alldodge

    5.7L with 1.62 gears, looking for advice

    Your boat isn't that old so 24 each should not be in the picture
Top