Search results

  1. alldodge

    '93 mercruiser 3.0l "neutral safety" adjustment?

    Its on the shift plate, just remove the wires and all it does is open and close contacts as the switch changes position. The shift plate is where the cables come to on top the motor, the switch looks like the one below. To adjust you need to have it in the center of the notch as shown.
  2. alldodge

    TKS Module Wiring

    Been trying to find a good wiring diagram to better illustrate how the TKS carb works. The TKS manual 41 is of help but not very good to visualize all the components are connected. Decided to make up a quick sketch for comment, and would like discussion on how better to illustrate. After...
  3. alldodge

    Do I really need a 4 way switch ?

    Like this
  4. alldodge

    Stuck spreader pin in steering pin!

    If I understand you correctly, you have drilled the holes in the top of the transom assembly and are trying to get the gimbal ring out. As in this pic If this is the case, it would be best to remove the motor since the yoke arm will not come off, otherwise you need a chisel and heat. Be...
  5. alldodge

    3.0L sputtering and won't go over 2k rpms

    At the beginning of the vid the motor appears to be idling above 1000 rpm's? The pic below was a snap shot after that time, but still looked like it was above 1k rpm. In the pic below the trim looks like the drive is full up, is this correct? I would do a compression test, the engine appears...
  6. alldodge

    Sea Ray Ford 351 won't accelerate under load

    Howdy Sounds like flooding and timing is out. What did you set timing at? Timing 10 BTDC Plugs Points .016 to .021 Dwell 26 to 31 degrees Firing order 1-3-7-2-6-5-4-8 (Note where No 1 cylinder location) Plugs AC (MR)43T (14mm) for serial numbers 4615130 thru 4616217 Plugs above 4616267 and...
  7. alldodge

    Engine swap, no voltage to gauges or ignition circuit

    The pic shows the lay out, but made it up to show how to bypass the kill switch
  8. alldodge

    Engine swap, no voltage to gauges or ignition circuit

    Howdy Don't think the 13V is accurate unless you have the bat on a charger when measuring. In any case, look down by the starter for something that looks like this It will be mounted on the starter post. Inside this is a 90 amp fuse, and it might have been blown. The fuse inside looks...
  9. alldodge

    Lateral gimbal misalignment problem

    Don't know which way is up, but if its straight up in this pic, and this is looking at the transom, then the motor needs to go down and starboard side a bit lower then port. And the bearing has been damaged
  10. alldodge

    Need TBI high pressure shreuder valve tool ???

    Suggest removing the fuel line and see what it looks like. This way might have a better idea of what you need. Here is another one for GM TBI note the O ring
  11. alldodge

    83 Chris Craft engine question

    Look on the transmission for the number and model. Being a direct drive it should be one of the ones below
  12. alldodge

    New motor, new ECM no start

    See if your getting 12V on the Pink and Pink/White wire of each injector
  13. alldodge

    Boat Lift Question

    Guess you could give it a go to see if it works. Moving both out would give you clearance. Maybe contact the manufacture to see if they have any comment. Looks like your dry weight with full tank of gas is 3740, then add gear and you should be within limits. Don't let anyone ride up or down...
  14. alldodge

    Boat Lift Question

    I understand what you want to do but do have concerns over the weight limit of the hoist. Your not able to extend the beam out further because this will put more stress on the hard ware. the lift is designed to lift with cable s straight and if the beam is extended on each side the will put...
  15. alldodge

    Boat Lift Question

    Who knows maybe the 3 post issue has changed, may need to check with iboats Tim (but cannot find him in the selection). Here are the pics
  16. alldodge

    Boat Lift Question

    I use this method
  17. alldodge

    Boat Lift Question

    Have no direct dealings with cable lifts but your dimensions tells me you don't have enough room. Could get into it a bit further but would need to know which make model is it? Assuming it something like this
  18. alldodge

    Boat trailer spindle removal

    Yep, fixed one like it years ago on my car trailer. Use a ban saw (I used portable hand type) to cut it off at the weld. If yours was flush welded like mine was, the pipe will be clean. Then get another spindle which has more shoulder and drive it into the pipe and weld it up. If you get the...
  19. alldodge

    1996 Polaris SLT 780

    The cone doesn't look like the parts in the breakdown Does look similar but not like a part. Item 24 is the wear ring http://www.polarispartshouse.com/oemparts/a/pol/5035e323f870023684114b03/propulsion-slt-780-intl-slt-780-i964588
  20. alldodge

    83 Chris Craft engine question

    LH has always been standard and is determined by looking at the flywheel, so looking at the front of the motor it rotates RH or CW
View older results
Top