Search results

  1. alldodge

    Crownline 1993 250 CR Securing the anchor on the bow

    :welcome: to iboats There are several methods and most all of them require you to install and chain holder. This one requires you to pull the pin before dropping and reinstall after it has be hoisted This one has a link which pulls the anchor tight after being hoisted, also needs to be...
  2. alldodge

    Bravo 3 Bellows Replacement - Times 2

    You right, Your starboard appears to be a Gen 2 gimbal and the port is a Bravo. Both have 4 inch spacing between the bottom flanges, but the spacing in the lower is wider for a Bravo then a Gen 2. Check spacing and see what it is
  3. alldodge

    Transom Bolt hole size

    Need to redrill the holes in my transom, anyone know what size the holes are. My 9/16 bit barely goes in on the two holes I won't be redrilling, but this is also wood. The studs are 7/16 so going to 1/2 would work and could redrill if needed "IF" I can manage to keep the drill in the center
  4. alldodge

    Converting from old exhaust to newer dry joint exhaust

    According to what I find is the hole goes to the highest side of the manifold, which in most cases is in the front
  5. alldodge

    Please help....new fuel pump wiring

    Swap the S and I terminals, you have it backwards. The S (N or NC) terminal is the start terminal, and I (NO) is the ignition (used after the engine is running)
  6. alldodge

    Formula 27PC Transom Work

    Epoxy paint on the under side of the wood Installed the deck over the fuel tank Cut the holes and foamed tank area
  7. alldodge

    Teleflex Tachometer wiring

    :welcome: to iboats If this is a sterndrive here is the wiring diagram
  8. alldodge

    Mercruiser 5.0 Running Hot at Idle Even After Many Component Change PLEASE HELP!!!!

    The engine pump tries to move water into the block, if the thermostat is closed, most water moves to the exhaust. When thermostat opens more fresh water moves into engine. My guess is the circulating water pump should never reach 170, maybe 140 - 150
  9. alldodge

    Formula 27PC Transom Work

    Have three layers on the transom and started putting the stringers in and coated them with the first layer. Installed the water and fuel tank, and have been cutting wood for the deck. In the next couple hope to be pouring foam in. After that, finish up on the transom and stringers then paint...
  10. alldodge

    Troubleshooting 1998 350 Magnum no start issue advice

    Looks like you have a TB-V setup, here is the troubleshooting guide. You will also need a meter, not a test light to check voltage.
  11. alldodge

    Totally intermittent alarm 5.0 Mercruiser Alpha 1 drive...

    :welcome: to iboats There can be a few things which can cause the alarm to go off, even a bad connection. Low battery voltage, bad ground but in most cases it turns out to be the water pressure sensor. Your sensor will be on the top rear of the engine which is attached to the power steering...
  12. alldodge

    Mercruiser 383 stroker water pressure sensor resistance values

    Here is what I have saved from other threads
  13. alldodge

    Motor Alignment Alpha 1 Gen 2 - Please help

    With the gimbal bearing area made smaller then 1.375, this should allow the bar to come out even easier. If the 1.150 front dimension is made to spec and has the forward chamfer, then I would start looking at the engine coupler. If the engine was out of alignment and sat for some time the...
  14. alldodge

    Gear Lube Monitor Reservoir / 2005 Bravo 3/5.0MPI

    Here is your setup, so if it is leaking from the barbed fitting, then a tighten or hose replacement may be the way to go. Note the barbed fitting is replaceable.
  15. alldodge

    Alpha One trim limit switch adjustment

    Here is the procedure
  16. alldodge

    What are these parts called?

    You don't need the gasket, your running on the water and don't have to worry about sucking in dirt. This is why you have a flame arrestor and not a air filter. Remove the silicone and put it together dry If the plug your talking about is item 8, it's just a plug 19-824928001
  17. alldodge

    Carb flooding after rebuild

    It takes very little pressure to seal off fuel from coming in the bowl. If properly adjusted there should be no leakage unless there is a speck of dirt or something in the valve. The adjustment is made by bending the tang in the pic below.
  18. alldodge

    7.4 electric fuel pump

    Hope this helps
  19. alldodge

    Wetting technic for 1708

    Put on three layers today and all came out good. Started by coating the surface and waited for it to get tacky. Then laid 1708 and started soaking the layers with VE and a 4 inch roller. The layer went clear and smoothed it out. In about another hour that layer got tacky, so we laid another...
  20. alldodge

    Wetting technic for 1708

    I need someone to tell me exactly how to do the 1708. Don't tell me to wet it and roll it. Give me step by step, please. I just finished grinding all the 1708 and resin back off. I hear wet it first and then put it on. To wet it first will be as I see it a real mess. I don't have much...
Top