Search results

  1. Scott Danforth

    383 cheap fun build ideas

    to get 400-450 hp, your RPM on the top end will be over 5500. define budget? you have a cast crank, not going to survive 450hp too long, however would live at 400hp. ditch the rods, SCAT forged rods are cheaper than re-conditioning the factory cast rods. check prices on regrinding your crank...
  2. Scott Danforth

    OMC 5.7 V8 power loss

    make sure you use a dwell meter to set the points
  3. Scott Danforth

    Multifunctional Gauges

    the only thing effected by your particular gauges by the fact its a 2-stroke is the tach.
  4. Scott Danforth

    Mercruiser 140 head retorque proper technique

    per the felpro head gasket instructions https://drivcat.com/livedocs/CI1963.pdf if you were going to re-torque (primarily for extreme use such as racing), you should have done it after the first time it ran and then cooled down however I have only ever done an initial torque and run on felpro...
  5. Scott Danforth

    surface tissue

    my guess its just CSM. however you need to sand and fair regardless of what you put on there.
  6. Scott Danforth

    Mercruiser 140 head retorque proper technique

    it really depends on the head gasket you used. was it a stock GM gasket? a Felpro metal gasket? a cometic? many gasket types do not require a re-torque.
  7. Scott Danforth

    2001 mercruiser 305 alpha drive to couple year older 350 engine

    as long as the 350 is a 1996 and newer, its a bolt in, align, mount drive and go type of thing should be relatively easy assuming its a 1986 and up.
  8. Scott Danforth

    1985 OMC 800 stringer with 350 chevy small block

    here is the link to get a factory manual. https://outboardbooks.com/ really wish you would have come here to the forum prior to your purchase.
  9. Scott Danforth

    Volvo Penta 5.7GSI PEFS ignition control Module

    the whole delco EST distributor is about $100 here is the module for $25...
  10. Scott Danforth

    AQ125 Oil pan

    it does make things easier if you have the motor and PDS hanging from the hook. that way if the PDS is rusted to the coupler splines, you can use a PFH and a BF-Pry Bar and get it off. and then you can replace the PDS bearings. Not to mention its longer to get to the dust shield screws from...
  11. Scott Danforth

    OMC 2.5L paired with OMC Sterndrive 800 Outdrive

    I would tell you to walk away from a 2.5 and anything OMC. you dont have enough motor to have a higher top end. even properly paired with a stringer 400, you were looking at 35mph max. the 3.0 could potentially muster 40mph. if the gearing was low enough (say from a 3.8) and they managed...
  12. Scott Danforth

    1988 Rogue 2420

    just playing with the media button on the new iBoats Xenforo. apparently cant link..... FiretrUCK however I an upload again.
  13. 1988-Rogue

    1988-Rogue

    misc-pictures
  14. 0209201141b.jpg

    0209201141b.jpg

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
  15. boat-with-slide.jpg

    boat-with-slide.jpg

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
  16. image_307551.png

    image_307551.png

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
  17. IMG_20140621_192517_715.jpg

    IMG_20140621_192517_715.jpg

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
  18. IMG00229.jpg

    IMG00229.jpg

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
  19. IMG00595.jpg

    IMG00595.jpg

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
  20. IMG-20110801-00278.jpg

    IMG-20110801-00278.jpg

    • Scott Danforth
    • Media item
    • Comments: 0
    • Album: 1988-Rogue
Top