Search results

  1. R

    Brass fittings on boats

    I was coaching a new boat owner / sailor last season.-----Made up a list of things to do / inspect while boat built in 1978 is lifted out for the season.----Next season I plan to spring the " person overboard " drill.---Also planning to do the " water higher than my shoes " on the cabin sole...
  2. R

    '56 Lark - Piston wrist pins

    Post the part numbers here.------Post the wrist pin diameter.----Post hole diameter in piston , both sides.----Compare with old parts.
  3. R

    2000 90ELPTO: Which sleeve: L130OB or L167OB? (short or long exhaust port notch)

    Buy 3 of the short ones.-----Make them long if need be.-----Agree with above post, boring the existing sleeves for O/S piston and rings is so much cheaper.-----
  4. R

    Pump themed anchor

    It is good for a " lunch hook " , it is not a functional anchor.
  5. R

    Your Best Technique for Rope Starting Merc 20hp EFI

    Many folks today are not familiar with simple mechanical things.----They are very good with the buttons on a phone.
  6. R

    Your Best Technique for Rope Starting Merc 20hp EFI

    See a dealer and get the lowdown on starting this motor.-----Or read and heed a manual.
  7. R

    Difference between U.S. & Cdn. capacity plates

    How do airline pilots determine total " passenger load " before roaring away.
  8. R

    ‘91 merc 60hp overheating alarm buzzing

    Wiring short or defective buzzer?
  9. R

    Jeez! What happened to global warming

    Global warming / cooling has always happened oner the ages.-----We now have instruments to measure / record and broadcast the alarm.
  10. R

    Decompression valve

    In the 1950's the 35 HP Johnson / Evinrude had decompression activated by the recoil starter.----
  11. R

    Decompression valve

    Decompression is often automatic on the camshaft.------Stops working once engine has started.----Where did you read that a slow pull releases it?
  12. R

    Upgrades for 92’ 25hp Johnson to gain some more speed!

    Hole in the 25 HP intake manifold can be opened up.-----Knowing that the motor has a 30 / 35 HP carburetor will automatically make it " feel " so much faster.
  13. R

    Upgrades for 92’ 25hp Johnson to gain some more speed!

    Step #1 is to determine condition of the motor.----Find a shop that can run it with a test wheel / prop.-----Or find a 30 ( prop rated ) or older 35 HP carburetor.
  14. R

    2018 Yamaha 40 HP, Poor top Speed

    Start motor.----Set at idle.-----Remove 1 plug wire at a time.----Post results of this test.
  15. R

    2018 Yamaha 40 HP, Poor top Speed

    On a 4 stroke the 180 PSI might be normal.
  16. R

    1994 Evinrude 50 HP Not Charging

    Find a wiring diagram online.----mastertech marine.-----Early 1990's V-4.----Wiring is the same / nearly the same as your 50 HP.
  17. R

    1994 Evinrude 50 HP Not Charging

    The " jumper " connects all the reds togerher.-----One red feeds 12 volts to ignition switch,----One red is 12 volts + to charge the battery.------The third red wire feeds power trim / tilt on this motor.---Usually the little cover for the terminal strip has the wiring explained.
  18. R

    1994 Evinrude 50 HP Not Charging

    The picture in post #1 does NOT show the jumper.----The parts page shows the jumper is needed.
  19. R

    1994 Evinrude 50 HP Not Charging

    There is a wee part missing on the terminal strip !----Item #4------Called terminal strip jumper.-----Simple to me.
  20. R

    1956 Lark +.20 bore - piston ring search

    visit----aomci-----Lots of greyhaired folks that may respond to a " wanted " ad if you post there.
Top