Search results

  1. bruceb58

    Maybe my turn for new boat time

    I have two boats that get moored on lakes. Neither one needs to be painted.
  2. bruceb58

    Maybe my turn for new boat time

    I said I would never buy a boat with bottom paint...that is my choice since I don't need it! since I am either always in fresh water or in salt for just a day
  3. bruceb58

    Maybe my turn for new boat time

    I don't keep my boat moored in salt water. Bottom paint slows the boat down and looks horrible.
  4. bruceb58

    Grease Seal to Spindle Fit

    The whole purpose of a bearing buddy is to keep the hub slightly pressurized. You properly pack the bearings by hand to get the grease into the bearings. You don't use the axles with the zerks to grease the bearings. You hand pack them.
  5. bruceb58

    Maybe my turn for new boat time

    I would never buy a boat with bottom paint...unless I was going to be moored in salt water which would never happen.
  6. bruceb58

    Maybe my turn for new boat time

    Both of my boats only get used from May to October. In my mind, its makes no sense paying high interest on a boat ever...no matter how much you use it.
  7. bruceb58

    Maybe my turn for new boat time

    I bought my 2025 Bennington Pontoon last August 30% off list. Boat sales are currently WAY down. I always pay cash for boats....cars too for the most part unless they are offering a really low interest rate which ios less I am making in a money market account.
  8. bruceb58

    Maybe my turn for new boat time

    Right now, 30% off is easy on a Cobalt. Not sure what Formulas are but I bet similar.
  9. bruceb58

    Budget friendly MEFI 1 communication tool

    Do you have TBI or MPI? I have a Rinda Diacom for two of the boats I have. It may be overlkill for your engine since there aren't that many parameters. The blinking light is goo if there are codes set but it won't tell you the following which the Rinda Diacom will tell you. Might be too...
  10. bruceb58

    Maybe my turn for new boat time

    And you bought his type boat to get away from sterndrives! When it comes time to buy my new Cobalt, its going to be hard to switch to outboard.
  11. bruceb58

    Omc outdrive knocking noise while cruising.

    On newer Cobras, they use a different bushing for the bellcrank that has a zerk fitting which allows you to fill with grease with a grease gun after you put it all together. You basically punch the old one out and tap the new one in place. I did that with my 87 Cobra.
  12. bruceb58

    2025/'26 CFB Playoffs

    OSU is changing their yell... O-H-I-O is now O-H-N-O
  13. bruceb58

    2025/'26 CFB Playoffs

    https://x.com/i/status/2006870647570575605...
  14. bruceb58

    2025/'26 CFB Playoffs

    OSU played horrible in first half. Played much better in 2nd. Miami has a GREAT defense.
  15. bruceb58

    Side Bunk Placement

    Mine have always been 2x6.
  16. bruceb58

    Proper Boat Grounding

    Of course it is...you just don't use it as a conductor for the return path for a load.
  17. bruceb58

    Volvo Penta engine coupler runout … aka wobble

    If it were my boat, I would be putting in a new coupler.
  18. bruceb58

    Installing a trolling motor on a 21ft CC

    Depends on the specs for the cells although most are spec'd at 1C or 0.5C . Most of the time, it's the BMS itself that limits the current and the cells are capable of more. These 50AH cells are actually rated at 3C https://www.evlithium.com/hot-lithium-battery/945.html As far as the number of...
  19. bruceb58

    Proper Boat Grounding

    You still need the ground to bond to the water pipe in addition to the grounding rod. In addition, you need a bonding connection between the hot side to the cold side and to a gas line(All usually done at the water heater) for current code. Most people who put in ground rods, if they didn't...
  20. bruceb58

    Installing a trolling motor on a 21ft CC

    In addition to your confusion of capacity vs current. most small 50AH batteries will likely only be able to put out 50A so 3 of them will put out 150A max wired in parallel.
Top