Search results

  1. CAPTKEV85

    breaking up while under load

    mercruiser 470 Had a great day on the water. New head and gasket. My overheating issue is finally gone. But I ran the boat for about 2 hours at 3200 rpms cruising. Then came into the canal and she was running a little rough. I know 470's idle for crap. So I decided to go out again and once I...
  2. CAPTKEV85

    Mercruiser 470 Distributor

    So i decided to put a new cap and rotor on, and of course the threads on the distributor to attached the cap to a wiped. Can this be helicoiled? Or do I have to go and buy a 500.00 distributor.
  3. CAPTKEV85

    Shifting Issues

    so I put a new water pump in my outdrive. When i put it back together i actually had the drive in reverse instead of drive. When I put it on the boat it wouldnt shift to neutral or drive. So I split the drive and put the drive in forward. The prop spins clockwise and the shaft spins...
  4. CAPTKEV85

    1977 Mercruiser Pre Alpha Drive

    so my mechanic gave me a free upper freshly rebuilt. So last weekend i decided to swap the uppers. I bought a water pump kit and when i pulled the pump off thewas alot of lower unit fluid, when i move the shaft more oil comes out. So I called my mechanic and he said its the water pump base thats...
  5. CAPTKEV85

    Tac question

    When my boat is running at an idle or on plane the tac needle jumps around doesnt stay were its supposed to. Is the tac bad?
  6. CAPTKEV85

    Gimbal bearing and shift cable

    So my Boat hauler came over on sunday to do the gimbal bearing, and shift cable. Thank god he did it. You need good set of tools and special tools to do the job right. My motor and drive have been misaligned for 3 years. I always had difficulty installing the drive every year. When he put the...
  7. CAPTKEV85

    sea water pump issue

    i just ran my boat yesterday with hose. when it was running i noticed that the was water leaking between the lower unit and upper. Last time i did the water pump there was a plastic peice that was melted. I replaced it but I haven't pulled them apart yet. Any ideas. also on the upper unit theres...
  8. CAPTKEV85

    WATER pump in drive question

    i just ran my boat today with hose. when it was running i noticed that the was water leaking between the lower unit and upper. Last time i did the water pump there was a plastic peice that was melted. I replaced it but I haven't pulled them apart yet. Any ideas.
  9. CAPTKEV85

    Great Stuff Foam

    can this be used in between stringers???
  10. CAPTKEV85

    Gunwales Have Slight Movement

    I HAVE A 1977 proline 24. Its an odd boat design but i love it. Downeaster bow and flattens out to a very shallow v in the back. I have a small cuddy cabin up front and 20 feet of open space behind the cabin. open deck. she has an i/o 470 merc. The floor and the stringers were rotted. so i took...
  11. CAPTKEV85

    Back With The Wounderful 470

    Well all summer I had an over heating issue about 15 minutes being under a load. 3000rpms the boat would run great. push it a little more and about 5 minutes a 3500 she would run hot and then push antifreeze out of the resivour bottle. This motor is driving me nuts. I did another compression...
  12. CAPTKEV85

    Walter Vdrives?

    I'm trying to help my father inlaw with his 1983 carver 33 has twin crusader 270's. hes owned it since 1985, and now is selling it to retire and live on his 43ft power catamaran in the bvi. the caver is forsale and the middle of the summer the vdrive is leaking. we found out that the bottom of...
  13. CAPTKEV85

    Tach needle is moving?

    when i am at a steady rpm. my tach rises and falls and the eventually goes back to normal. i have a new coil and electronic ignition. merc 470 1977. is my tach bad?
  14. CAPTKEV85

    Grinding While Goining Into Gear Merc 470

    back again guys, just some advice. When i put the boat in gear she grinds then engages. So i replaced the shift cables both of them. then I replaced the control. still does it. so then i play with the adjustments for hours and it either goes in one gear perfect and grinds in the other. I...
  15. CAPTKEV85

    compression check on 77 merc 470 :(

    today i did a compression check on my wonderful 470. i let the engine come up to operating temp. then shut it down and pulled number 1 plug. put tester in cranked engine. psi was 130. check #2 psi 130 checked #3 115 checked #4 130. so obviously #3 is a problem to my overheating and air getting...
  16. CAPTKEV85

    Now Im Overheating My 470 Merc

    -------------------------------------------------------------------------------- I love the power of this motor but hate it just as much. fresh rebuild this year. put the boat in around april. three test runs, each time one coolant hoses popped then boat overheated. mind you this is a fresh...
  17. CAPTKEV85

    Another Merc 470 Issue Again!!!!!!

    I love the power of this motor but hate it just as much. fresh rebuild this year. put the boat in around april. three test runs, each time one coolant hoses popped then boat overheated. mind you this is a fresh rebuild. Posted a forum back then, couple of guys said possible defective head...
  18. CAPTKEV85

    Mercruiser 470 Outdrive Grinding In Gear

    1977 mercruiser 470 with pre alpha drive. i purchased a new shift control,cables,still grinding. i have spent hours adjusting the cables. it eithers goes into fwd easy and grinds in rev, or the opposite, i also replace the shift kill switch. any i deas ? i just want to put it in gear with...
  19. CAPTKEV85

    Westerbeke Generator 7 Kw Overheating

    Im Leaving To Hemlock Cove Today And My Gene Is Overheating. Thermostat Is Working Fresh Water Pump Working. I Put A New Impellor In The Sea Water Pump. Still Shutting Down. Any Ideas????
  20. CAPTKEV85

    Why Is There Water Shooting Out Of Resv

    1977 mercruiser 470 new rebuilt. just put in the water and a hose blew while under plane. replace hose and then when out for another test drive and then the radiator cap was whistling like a locomotive and overheated. all hoses swelled up and look like the wanted to pop. any ideas i think its...
Top