Search results

  1. C

    Motor

    I have rebuild my transom on 1996 keener 21 ft CC then I Installed the motor, its not right because the left rear digs deep when I take off and the rooster tail sprays high on the right side. Im going to install a jack plate and bigger motor, I. Going to plug the top holes, how do I...
  2. C

    Motor support racks

    Im needing to build a rach to hold (2) johnson 150 and (1) 200. How wide and how far apart should the wheels be to support these three motors
  3. C

    Motor lift plate

    Thanks, im going to buy the lift
  4. C

    Motor lift plate

    They say they will hold 225
  5. C

    Motor lift plate

    I bought a c ouple of 96 johnson 200. They are 25 in. My boat is 20 in. I have found lift plates to raise it 5 inches, that are rated for 225. They look like 12 aluminum angle iron. Jas any one ever used them? I have seen manual jack plates, are they necessary?
  6. C

    Lowrance warranty

    I think you jave a good point. Battery 2. At the console was lower. So i swith to Battery 1&2 to charge 2 while running.
  7. C

    Lowrance warranty

    Lowrance elite fs 9 i bought the unit and it sat in the box over 3 years. The sonar went blank. I ran troughtrouble shooting with them on the phone for ever. Then they told me to send it in. 40 for testing 440 for a replacement. They send me a newer model brand new. I guess. 5 time on the water...
  8. C

    Rebuilt floor question.

    Can this be corrected by adjusting the motor? Im to deep into this project to do anything but adjusting the motor..this was the first and last floor and transom I'll ever. It cost more than buying another hull. The man hours spent alone by myself rebuilding. I never thought about the...
  9. C

    Rebuilt floor question.

    No.but changed motors a couple of months ago and did the same thing. I definitely with checking out. Im also running without my hydro foil. I have noticed the propeller throwing water up out of the lake on the right side. i related that to not have the foil installed
  10. C

    Rebuilt floor question.

    1996 21 kenner CC I did a total floor stringers and transom rebuild. I drilled holes 24" ft. Apart. Then mixed my foam and poured it in the holes until it expanded out the others. Some times I didn't have enough, so i added more. I assumed it filled the void. I used a level from side to side to...
  11. C

    Transon mounted trolling motor

    I have 21 center console boat. I have an 80 trust on the front with foot control. I want to add a hand sterring clamp style on the transom. Will a 50 lb. Work the slowly move my boat I want an pilot but now is not the time. Im looking for a used one.
  12. C

    Mercury TT

    I have One for sale, and I found a guy needing it. I was going to help replace it. I haven't seen his but it might be rebuilded. Not sure
  13. C

    Mercury TT

    I dont have the model # I have 99 200 TT. Does it interchange with an 86 TT?
  14. C

    Seastar hydrolic steering testing

    Lines don't need to be "sterile". Flush with clean hydraulic fluid What do i use to clean the inside pump and cylinder i bought a new plunger for it. I want it clean. As possible. Thanks
  15. C

    Seastar hydrolic steering testing

    Once the pump cylinders are connected at the console. They would be like turning a cup upside down and pushing it into water. The air has no place to go. Are the design to hold air? Like a shock exorber? Im disassembling, it tomorrow. I'll send pictures to explain the questions i'm asking
  16. C

    Seastar hydrolic steering testing

  17. C

    Seastar hydrolic steering testing

    Ok I'm ready to flush the lines a clean the pump. Do I use gas, parts cleaner in a can or acetone? When in putting the plungers back in should I lube them with hydraulic fluid? I have one stupid question. With the 7 plungers facing down. How does the air get out of them once installed. Should...
  18. C

    Seastar hydrolic steering testing

    I tested the pump with the lines disconnected using a 1/4 valve and gauge on each hose, i could see it moving pressure from one line to the other... It's a bad plunger... thank for responding.
  19. C

    Seastar hydrolic steering testing

    I found the problem, the polymer seal on the plunger is letting fluid through. I stopped testing pressure at 300. That's all my gauge read, I could get more press. I have found a company that sells the rod with the plunger and seal together. For about 125.00 I couldn't find the o-ring and the...
  20. C

    Seastar hydrolic steering testing

    I'm having problems after I hit the motor putting extreme pressure on. I lost my steering. Things done i have bleedit to death many times. I have removed it an totally disassembled it twice, every thing was oily and spotless clean, removed the 4 springs and ball bearing twice. Secondtime I...
Top