Search results

  1. Scott06

    What oil should I use?

    Exactly my similar vintage 3.0 had same cap on valve cover but merc documentation recommended straight 30 w or 40 w depending on ambient temps
  2. Scott06

    5.0 oil weight and amount

    Would not think so unless you have a very odd situation with stringers
  3. Scott06

    2012 seadoo rxp 260 only goes 30mph

    Do the supercharger rebuild by the hours , my neighbors friend has same ski asked him about it if he had rebuilt the supercharger he said no seemed fine … he is now replacing his engine .., Defiantly would look if you are missing spark on a cylinder and replace the plugs Have found a cheap...
  4. Scott06

    Got a new toy to test out eventually...

    I got best results with a revolution 4 vs a Enertia. Enertia is a very good prop but might not be best for every application. Would think even with bottom of the V is in a good spot
  5. Scott06

    Got a new toy to test out eventually...

    you can trim the annode with a grinder or get the flat one. Very common for props to hit them other than basic Black Max Al ones
  6. Scott06

    Does the antifreeze you use really matter?

    You are not wrong there are only 2 drain plugs on the 4 cylinder. IF you have power steering you may need to pop a hose off the PS cooler if it traps water. I'm not far south of you in upstate NY and do as mentioned - drain fully, I use about a gallon to splash back into the hoses to chase any...
  7. Scott06

    U-joint Bellows & Upper Shift Shaft Bushing

    Agreed that bushing and seal assy is pressed in the bellhousing lightly. On the bellows adhesive - only put it on the areas where the bellows and lip on transom housing fit together just a light coating on the lip around the gimbal bearing and inside of the bellows where it seals on the lip...
  8. Scott06

    I have a leak.

    Sounds doubtful at best. I would be looking that the bellows are not leaking depending on position of the drive L/R & Up/Dn , or there is another leak in the cooling system Have you looked at the driveshaft bellows closely ?
  9. Scott06

    Bellows Installation

    Yeah the newer style push on hoses are pretty cool, no clamps required . I use them a lot at work ( in larger sizes) to make air and water hoses on site with no end crimping tools.
  10. Scott06

    engine oil

    Rotella T4 Conventional 15W-40
  11. Scott06

    4.3 mercruiser vortec issue

    After it is assembled Take the plugs turn it by hand to ensure geometry is correct and nothing is hitting
  12. Scott06

    Another Winterization Thread!

    $200 buys a lot of beer…
  13. Scott06

    Mercruiser 4.3 Prop Question

    Also check the tach vs a shop tach. Would not think if you had soooo much pitch that wot was 3800 that you would have the great holeshot that you mentioned. either rpms are off or there is a tune up issue have you verified timing both intial and total? and what do the plugs look like
  14. Scott06

    Bravo 3 Refresh Questions

    Look closely at the corrosion a buddy of mine had to replace his lower housing as it cracked by bearing carrier due to corrosion. I think the later ones had two annodes on the cav plate vs the original single one. Ultimately he ended up putting a second mercathode system on it with transom...
  15. Scott06

    4.3 mercruiser vortec issue

    the push rod is moving ?? I understand the valve is closed but the pushrod should not be moving down unless the lifter is collapsed or lifter is not on the cam fully, or is the pushrod not seated against the lifter? Is this the same for all rockers? No milling the head for warpage would not...
  16. Scott06

    What oil should I use?

    Use the T4 conventional rotella . It has enough zinc for flat tapped cams And is an excellent value
  17. Scott06

    Outside lower unit will not go up

    Not owners manual get the mercruiser shop manuals for your engine and drive serial numbers. If you post the serial numbers people here can confirm which manuals to get. I got mine used off ebay invaluable if you plan to work on your boat
  18. Scott06

    Outside lower unit will not go up

    First pic is the trim limit switch so definitely the trailer button will only make it go up - do you have a manual with wiring diagram looks like you have some wiring stuff to work through
  19. Scott06

    5.0 oil weight and amount

    Change it annually with a good quality oil and filter and you will be ok, engine will outlive the boat. Check the oil level before use and it will outlive the boat. Winterize it properly by draining and it will outlive the boat... you get the idea... You didn't say what year the engine is im...
  20. Scott06

    Mercruiser 5.0 Mpi issue

    Yeah but all of those hours were tapping the rev limiter, trimmed out testing your garage full of props.... I just hit 400 hrs, boat is 20 years but engine that was installed after PO owner cracked the block is 9 yrs /360 of those hrs.
Top