Search results

  1. Stinnett21

    Prop suggestions please

    A 9.9 pushing a 21 pontoon would, most likely, require lowest pitch possible which looks like 7 inches according to iboats prop finder. But to really tie it down you need to gather information first. Many, many threads on this site to take you through this process.
  2. Stinnett21

    Considering '13 Bayliner 215

    Go outboard if you can. The maintenance on the I/O gets tiresome and pricey.
  3. Stinnett21

    5.0 Mercruiser MPI Broken distributor Screw hole

    Not sure what you are talking about. Can you include a pic?
  4. Stinnett21

    5.0 mph belt routing

    Sometimes the tensioner can seem like its loose all the way but its not. It can kinda bind. Use a 5/16 deep socket on it. Sorry, not questioning you. Just stating my experience.
  5. Stinnett21

    Exhaust Bellows

    No more than with the bellows attached. Think about it...at rest with engine off water is consistently occupying the Y-pipe inside the boat, level with the water outside the boat with either bellows or tube. Now I have heard the argument that if you slip your boat or beach a lot the tube may...
  6. Stinnett21

    Boat mooring in rocky areas (aluminum boat)

    But how do you get back in the boat? Also I don't understand the OPs sentence..."Bumpers feel like they might work in all cases". Check out Keelshield for aluminum boats.
  7. Stinnett21

    Mercrusier 5.0 MPI (2008) RPM stops @ 3200.

    I read that too that's why I didn't suggest it. I change mine on my MPI about every two or three years now that the internet has made me aware of the issue. Easy job and not pricey. I will say however my original one lasted 15 seasons and 1000 hours before needing replacement, go figure.
  8. Stinnett21

    Bell housing to outdrive gasket protruding

    Think I figured it out. You mean prior to install sand the bead. Gotcha. I'll be doing this for a buddy soon so wanted to be prepared. I've done mine several times and never had it pop out but evidently it's an issue. Goes without saying I suppose but ya gotta take the six nuts in slow...
  9. Stinnett21

    Bell housing to outdrive gasket protruding

    Not sure what you're saying in #3. Can you unpack that more please?
  10. Stinnett21

    Mercrusier 5.0 MPI (2008) RPM stops @ 3200.

    Just curious, when you attempt to go past 3200 what happens?
  11. Stinnett21

    Single point drain winterization

    Nice work Lou. I've just been biting the bullet and dissembling it all as it was built but not sure how much longer I"m willing to tolerate it all at my age. Sorry I left my portable toilet in the pic.
  12. Stinnett21

    Single point drain winterization

    Access is the problem. Had engine builders worked with boat builders in designing interiors that were more mechanic friendly maybe the I/O would still have life left in it. For example why not make the panels on each side of the engine folding and attached with buckles or some sort of quick...
  13. Stinnett21

    Single point drain winterization

    This is what I do also. I've owned this system new since 2002. I pull the quick disconnects on each side of the block and poke the holes. Some years I will pull a few hoses and poke them also. Never found a block. Now to be fair I'm 100% fresh water.
  14. Stinnett21

    Buying a 2021 Sylvan!!

    Fenders: Buy the largest storage will allow. I hate it when boaters drag them along deployed full time. Horn: Relax your factory horn will be sufficient.
  15. Stinnett21

    2003 20hp Mercury prop

    Amazon.
  16. Stinnett21

    Engine starts to sputter/breakup/lose power after warm 3.0 ‘98

    Borrow a fishing buddies remote tank to run it on to eliminate one side of the equation.
  17. Stinnett21

    New to me 2015 350 mag, any more maintenance items?

    Probably. Mine is a small white filtery/foamy looking thing. As they age with use they turn black. If yours isn't gunked up you're fine to leave it. But as cheap as it is I replace yearly. Amazing the trouble they can cause if not attended to over time.
  18. Stinnett21

    New to me 2015 350 mag, any more maintenance items?

    Replace IAC muffler. Also, you said props so assume it's a Bravo 3? Look... I know it's expensive but buy, and/or build, a drive dolly and check alignment yourself. Shops say they do it, my experience? They never do it. It takes two guys and bunch of time. If it's halfway close they shove...
  19. Stinnett21

    2000 Searay vapor lock

    Mine is #2 in the attached. Port side low and back. Yours may be entirely different.
  20. Stinnett21

    Bow plowing at high speed.

    Prop gurus are always talking about bow lifting vs stern lifting props. Can't tell exactly what yours is but you might post it on the prop forum and ask what it's characteristics are. It may be that a prop noted for its bow lifting properties could help. Just a thought.
Top