Search results

  1. alldodge

    We had a bit of wind last night

    That's a big pine. Cut a smaller one down yesterday and pushed it over the hill.
  2. alldodge

    Exhaust to Gimbal Connection

    It just list to use it, no mention of how much I would probably use a liberal amount, won't hurt
  3. alldodge

    Exhaust to Gimbal Connection

    Manual list to use 92-25234 Sound blanket glue, but this has been superseded by Bellows adhesive 86166Q1
  4. alldodge

    Alpha One Gen II Lower Unit - Drive Shaft Binds When Tightening Retainer

    I'm having trouble following your comments, maybe it's the terms This is talking lower You pulled the lower apart but did not disassemble anything on the prop shaft side. So what exactly did you take apart???? This is talking upper Got the pinion gear nut installed, then tighten drive shaft...
  5. alldodge

    454 Water pump hoses

    Post a pic of the front of your motor with also showing the thermostat housing
  6. alldodge

    Mercruiser motor swap

    Moved it to Merc from FAQ area
  7. alldodge

    Metal O-Ring appeared on alignment tool

    The ones I've worked on have been housing Manual says to remove with a slide hammer, but sometimes they get frozen
  8. alldodge

    why is there oil in my bellows but pressure test holds 15psi overnight

    Don't see it being grease, that said the new bearings are sealed but there are thousands of the old style still out there that get greased
  9. alldodge

    Metal O-Ring appeared on alignment tool

    The seal can be bent up to get it out. Others may have a better idea, but take a long screw drive and smack it
  10. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Guess I'll have to take you word for it. Being 2X the force than I don't see how the Crap --- arrel stays together going from a SSX 30 to a 280 OSX. I have no stringer extra anything inside the boat. Sure my 280 only has a 25.5 ft hull Than we can compare the Formula 310 sterndrive or OB, the...
  11. alldodge

    I/O (Sterndrive) Conversion to Outboards

    No engineer here I'm seeing the many structural supports built into the OB structure. Don't see how that will ever have a chance of failing. The boat came with twin 6.2's which has max HP rating of 350. All the force was placed on the original holes placed close together and there is no design...
  12. alldodge

    Alternator and fuel pump on Volvo Penta 3.0 GLP-D

    A fully charged resting Bat should read 12.7V that is after it has sat for an hour or so off the charger. Once motor has reved above 1500 RPM the ALT should show 14.5V Now the meter being used may be slightly off
  13. alldodge

    Ideas for planters/raised beds?

    I know folks that do no till and have great growing every year. 30 inch wide for plants and 18 inch wide for walk way It takes a couple years to get it working great, but after that all good
  14. alldodge

    Mercruiser 350 MAG MPI

    Your ECM post 4 shows the date of 2005 Being a 2005 your max WOT RPM is 4400-4800 per manual 31
  15. alldodge

    Merc 250 Verado Fuel increase

    I know what your talking about. Looked at these when running with the Rev 4 props with my buddy watching as RPMs increased to WOT. Will compare with the new props Wanted to take the boat out today and fill the tank with readings, but winds were up around 20 mph so if things work out I'll try...
  16. alldodge

    Metal O-Ring appeared on alignment tool

    That's the inner spine on a lip type seal. Probably from the grease seal behind the gimbal bearing Edit Bondo was quicker
  17. alldodge

    Ideas for planters/raised beds?

    TSC and rual king have 40 gal tanks for 179
  18. alldodge

    why is there oil in my bellows but pressure test holds 15psi overnight

    Try putting 5 to 7 psi in and rotate the drive shaft. Also try to move it up/down/side to side to see if you loose pressure. With a lip seal, the more pressure is applied the tighter the seal is forced against the shaft If all that works without leaks, try a vacuum at 3-5 inHg
  19. alldodge

    I/O (Sterndrive) Conversion to Outboards

    Forget the exact name of the product but something like Bondarite and used to adhere transom wood to hull
  20. alldodge

    Pushing Run-Flat tires to the limit

    Most are running low on blinker fluid
Top