Search results

  1. C

    1987 Mercury 9.9 B151689 Flywheel magnets

    I am not sure, but, I seem to remember the magnets have a beveled edge that goes down when installing.
  2. C

    Should I lube it?

    That was my guess, but I needed confirmation. Thank you so much.
  3. C

    Should I lube it?

    1990 Mercury 2 stroke 60 hp . Should there be any lube on trigger where it slides around? Installing new stator and switchbox, trigger checks good. Just wondering if it should be dry or lubed
  4. C

    Should I lube it?

    1990 Mercury 2 stroke 60 hp . Should there be any lube on trigger where it slides around?
  5. C

    Revolution limiter

    Is anyone familiar with a over rev control on 1999 Johnson / Evinrude engine? Was it included on these units?
  6. C

    p/n interchange for the 5.5 hp skeg

    Google ---Johnson 303335 ===lots on e-bay
  7. C

    carolina gator

    carolina gator
  8. C

    coil check values

    Thank you, my coils match all necessary specs, but I just could not understand why there was continuity between positive and negative posts. I just do not understand electricity. But they work, so I am satisfied.
  9. C

    coil check values

    Not just any thief. This was a Yamaha dealer, that admitted to pulling parts off to test customer's motor, so he said. He only had this motor in to sell for a friend. I had just redone carb and water pump kit for him . This was an 85 18XD with only 30 hours on it. Paint wasn't even scratched...
  10. C

    coil check values

    Using Fluke 110 meter. Just running through the procedure for checking electronics on this engine before trying to start it. Seems some one pilfered parts off it while it was in shop to be sold. Just want to determine what parts were taken and replaced with old ones. Beginning to think they may...
  11. C

    coil check values

    Sorry, there was supposed to be a picture and part # in the post. Didn't notice it was missing. It was stated that the specs shown were correct as tested. Only question is the + and - primary posts show 0 ohms but do show continuity. Should that be so, or a short to ground? Maybe it is supposed...
  12. C

    coil check values

    Strange that with the "experts" on here that no one has the answer. But, thanks for looking.
  13. C

    coil check values

    This Mercury coil reads correct values at all check points. But also shows connectivity between + and - terminals for primary. Would this make it a good or bad coil? Secondary 9.5 Primary 0.0
  14. C

    1968 6 HP Evinrude need help

    Yep,that's what I got. The 75 carb you mentioned uses same float bowl and upper body. So should work. My bad, the 75 uses a different upper body.
  15. C

    1968 6 HP Evinrude need help

    Yeah. I have two of them. I guess I better keep for spare. What was the price?
  16. C

    1968 6 HP Evinrude need help

    My research shows it will.
  17. C

    Help with figuring a boat out

    http://trulineboats.com.au/
  18. C

    Help with figuring a boat out

    Try this" https://www.searay.com/global/en/models/sun-sport-series.html
  19. C

    Comparing the model number on 1979 Evinrude 115999R to the stamped # on the block

    https://forums.iboats.com/threads/omc-1-6l-sea-drive-questions.357706/ This is interesting reading for anyone with your motor.
  20. C

    Comparing the model number on 1979 Evinrude 115999R to the stamped # on the block

    1.6L - Mechanical - XL 2BBLCOM 2BBXCOM 1979 look this up on crowleymarine.com for parts
Top