Search results

  1. C

    96 johnson j150exedb. Help with hoes location

    Thank for your help. I have a couole of more questing On page 3-40 1. The manul reads, connect the recirculatin hose to the hose, does refer to up and lower teed together? 2. Where is the pulse limiter valve? 3. Is this motor conciderrd a looper 4. Does this motor have cylinder block check...
  2. C

    96 johnson j150exedb. Help with hoes location

    I finished building motor i started a couple of yeas ago. I know the the fuel in, oil in , and pules limitter all connect to the bottom of the VRO and the 2 primer lines I dont know what hoses connets to the upper and lower barbs on the front a of the crank case cover. And I dont know...
  3. C

    Midsection 1996

    I cut the shaft out, it was bent and i could not pull it out from the top. I cut it out and droped it though the bottom. Bought a used onr. Woks fine
  4. C

    Lower unit leaking oil from weep hole.

    This hole and the top weep are conneted. Is this botton hole factery? Is it a damaged spot? No oil leaks from here with motor down.
  5. C

    Lower unit leaking oil from weep hole.

    Better pic
  6. C

    Lower unit leaking oil from weep hole.

    96 johnson 150exedb All new seals in lower unit. None are leaking. I tilted the motor all the way up last night. The leak is from a weep hole top front lower unit. I remove the lower unit. And the cove for the shifting. Under the cover in the middle there is a threaded hole 5/16 bolt hole. When i
  7. C

    Midsection 1996

    I have a johnson j150exedb. The shaft going down through the midsection is bent. I can't get it out. I'm looking a a motor for parts. What years are interchangeable with my motor?
  8. C

    96 johnson j150exedb lower unit

    My motor is a new rebuild as well. During 2 other run test, 10 to 15 minutes each. Pump pushing water out the pee hole with force. Problem started while running in gear 1000 to2000 rpms Motor was getting plenty of water when I did the first run on lower unit. I don't feel like the lack of...
  9. C

    96 johnson j150exedb lower unit

    I purched a old lower unit. Removed all parts cleaned and reassemble per manual. While test running is on a hose. After 30 minutes or so, water slowed down and motor was getting hot. Removed it this evening, the water pump housing had a gummy sticky stuff blocking the passages the impeller was...
  10. C

    Pedestal seat height for bow-mounted trolling motor

    What's a phone book?
  11. C

    Johnson wiring.

    My boat has the complete main wiring harness to the remote control panel. I need to find the plug for the instrument panel. I dont know what it call or if I can buy one. I'm trying to avoid cutting the plugs off.
  12. C

    96 john 150.

    I'm putting the started together. I have the bushing for part #20. What part above the bushing? The timing cover has a bushing as well.
  13. C

    1996 150 vacum lines

  14. C

    1996 150 vacum lines

    Th Thanks, next q Thanks for the information. I posted a picture of the lines on to of the fuel primer and fuel pump area. They are high lighted green. My donor motor had them plugged off. If the VRO is disconnected can I just keep them plugged?
  15. C

    1996 150 vacum lines

    J150exedb. I think I have figured out the tiny hose. Looks like it goes from top of the crankcase to the bottom. I can't find a diagram in my manual for the ( 2 green hoses) midsized hoses. I have connect the 2 lines for the primer and the 2 lines for the fuel rail. This motor has the vro...
  16. C

    1996 150 vacum lines

    I'm putting fuel/vacumlins on my boat. I can't figure out were the line goes. It the tiny fitting between the bottom carb and the
  17. C

    2000 mercury 200 efi loses power gradually as day progresses

    Sounds like the fuel pump is shorted when it's hot, this would also cause the scanner to lose power for sec
View older results
Top