Search results

  1. Franco_boater

    Lost trim gauge and water temp indications

    I have checked and looks normal to me… even I’ve wiggled and nothing
  2. Franco_boater

    Lost trim gauge and water temp indications

    Thanks for clarity, and do you know Which one of 2 wires is for the gauge I should check? But it worked before I put it in the trailer , after winter it’s gone…
  3. Franco_boater

    Lost trim gauge and water temp indications

    Thanks , Can you tell Me How to ground the sender ? Ok so 1. Cable connected to the Ground 1 side and 2 side to the wire from the gauge, should go to the right. 2. 12V Voltometer, 1 side to ground 2 side to wire from sender and should be 12V on the Display?
  4. Franco_boater

    Lost trim gauge and water temp indications

    I will have to find trim gauge wires , can you tell me where to search? I think it will be 2 wires right? But for the water temp sensor I’ve only 1 brown wire which goes to the sensor in the thermostat housing . Is that right? But actually both trim and water temp sensors are dead, full to the...
  5. Franco_boater

    Lost trim gauge and water temp indications

    1st step isn’t actually a grounding? Ground on 1 side gauge on the other = grounding right? I don’t get your instructions sorry I’m not English speaker like You
  6. Franco_boater

    Lost trim gauge and water temp indications

    Do You mean at the instrument gauges or at the engine bay?
  7. Franco_boater

    Lost trim gauge and water temp indications

    Hello thanks for fast reply. I’m good at turning wrenches but hate electrics :) can you please tell me how to check it. I have boat on the trailer so far … but wish to drop it finally
  8. Franco_boater

    Lost trim gauge and water temp indications

    Hello I wanted to put my boat into the water after winter. Boat runs great with new impeller and exhaust gaskets BUT… Trim gauge doesn’t work and water temp… Before winterisation everything was fine… How to check if the sensor is ok or check the signal to the gauges ?? Thank You for help When I...
  9. Franco_boater

    4.3 V6 leaks wet oil sump

    I will try to clean it as much as possible but its very tough there … No space Regards
  10. Franco_boater

    4.3 V6 leaks wet oil sump

    So the pan was bend in the factory already? What’s the problem at all? If I buy a new one what’s the chance it will be ok ?
  11. Franco_boater

    4.3 V6 leaks wet oil sump

    So timing cover and oil pan to replace..
  12. Franco_boater

    4.3 V6 leaks wet oil sump

    I will clean but I think front seal may be leaking or timing cover... anyway if its not possible to fix it while on the boat its done :/
  13. Franco_boater

    4.3 V6 leaks wet oil sump

    I’m sorry it’s 2005. I don’t think pan is rusted only paint is falling off. This oil maybe is a good rust protection :)
  14. Franco_boater

    4.3 V6 leaks wet oil sump

    Hello friends, I’ve noticed the oil pan is wet in oil, do You know the common places for leaks? I think it might be front seal and from the oil drain hose?? Is it possible to remove that leaks on the boat? I’m don’t have any major leaks I think it’s only wet But I like when things are as it...
  15. Franco_boater

    Engine alignment issue little marks on the side

    ok i will try to raise only port side and check again, 1/4 turn only
  16. Franco_boater

    Engine alignment issue little marks on the side

    Hello I’m trying to align my engine I have more visible marks at the bottom than at the top so I have to raise the engine a little right? Tool slides in easily but a little fires when out. But I’ve noticed that marks at 2-3 o clock are less visible than at the 8-9 o clock I was trying to turn...
  17. Franco_boater

    Swap from 3 Blade prop 19P to 4 blade prop

    now I’m using 3B-19p and I was generally happy even for top speed and hole but just wanted to experience something new… so here we are with wrong prop… Do you think it’s “safe” to use this 4B-19 during this season? Or I can stress gear /engine
  18. Franco_boater

    Swap from 3 Blade prop 19P to 4 blade prop

    Ehhh so I screwed up.. wanted to get on plane faster, I’m towing with family I’m not running at WOT …. It’s 19 footer bow rider
  19. Franco_boater

    Swap from 3 Blade prop 19P to 4 blade prop

    Hello, in Mercruiser section I’ve found discussion about running engine lean when swap from 3blade to 4 blade prop . So here’s my question Now I am using 3 blade 19P black diamond in alpha one gen 2, got 4 blade 19P Nemesis in good price, can I expect better hole shot and handling??
  20. Franco_boater

    Clanking/rattling sound after prop change

    Hello, Can i ask you one question? I was using 3 blade 19P, this year i bought 4 Blade Prop 19P to have better hole shot. both aluminium props I haven’t been boating yet . Alpha one gen 2, do you think It will generate some problems?
Top