Search results

  1. O

    2022 MerCruiser turns-no ignition

    My 2022- 350 MerCruiser MPI was running great until yesterday. The engine is turning over but does not show any kind of attempted ignition while the key is deployed to the start position. There are two symptoms -first just at the end of the turn cycle which is usually 6-8 revolutions and as I...
  2. O

    Stalling low speed outboard

    They have carburetors thank you for advice.
  3. O

    Stalling low speed outboard

  4. O

    Stalling low speed outboard

    Just purchased 2000 150 hp yamaha two stroke-runs great with cold start engaged or higher running rpms 1500 and above -does not hold an idle- before the stall it sounds like it is running out of gas-spits and stalls .Bulb remains hard. Will restart quickly with cold start engaged. Any help...
  5. O

    1989 35 hp yamaha sputter

    The engine overheat alarm sounded. Shut down engine-believe i sucked up some slip gut. Did a compression check -all good 135 both cylinders .Problem the engine starts and runs fine then sputters as if you turn key off and right back on. more consistent sputter in neutral every 5-10 seconds. in...
  6. O

    cmp 25 b vhf not working

    Thankyou regards andy
  7. O

    cmp 25 b vhf not working

    Tried some basic troubleshooting methods- the question is this- will the new standard horizon ram 3 marry up to the old receiver? are the remote mics interchangeable/ thank you for time
  8. O

    Gas leak while priming

    Great thank you for time and info Regards Andy
  9. O

    Gas leak while priming

    Would carburetor cleaner possibly work on stuck needle or do you think the carburetor should come off- gasket and bowel will also be looked into if the spray method is not advisable or does not work-looking to do easy things first? Thank you
  10. O

    Gas leak while priming

    2001 150 Johnson-gas leaking from bottom left carburetor [gas leaking through the open black throat that is exposed when the plastic air filter is off] while trying to prime. What are the possible reasons and solutions? Thank you
  11. O

    panels lights at bridge no on /off switch

    I will look into nav light switch issue as possible problem- it would make sense that if there is no dedicated panel switch maybe be a tie in to nav light switch. At least this trail now has a starting point-Thank you
  12. O

    panels lights at bridge no on /off switch

    The instrument panel on the bridge all gauges are lit up when the battery switch is turned on. All the switches are clearly marked with no panel switch indicated. No other switch controls the panel lights.
  13. O

    panels lights at bridge no on /off switch

    Just purchased a 1999 Phoenix 29 SFX. The other night I noticed the panel lights were on and there does not appear to be a switch to turn them off. The only method is to turn off batteries. This seems odd by design -any knowledge of this boat and its design is appreciated.
  14. O

    power trim-slow death

    I have a 2000 150 h.p. Johnson -trim motor replaced 6 years ago-Last week or so motor running slower and slower especially when full trim up or down. Now nothing -battery in good shape. Are there any trouble shooting options or is this probably a replacement situation. Thank you
  15. O

    power trim not working

    evinrude
  16. O

    power trim not working

    2016 60 hp tiller handle trim motor responds intermittently neither switch/handle or motor works most of time/ seems electrical any idea's would be helpful
  17. O

    Slipping belt

    serpentine belt -straight inboards
  18. O

    Slipping belt

    Are the pulleys adjustable-I looked at same boat and motor setup that was for sale and on the work list from yard they stated they had to build a stabilizing bracket for the alternator bracket due to a high rpm flexing issue. Yard is closed today would like to find out more info. Phoenix 29...
  19. O

    Slipping belt

  20. O

    Slipping belt

    I have a belt issue on my 2000- 300 h.p. mercury inboard -Is there any part in the pulley system that is possibly more responsible for proper alignment of the belt so that it does not get damaged or breaks as a result? I had a mechanic install a new one and said everything looked fine. If there...
Top