Search results

  1. Bondo

    How to remove my engine

    Ayuh,...... Welcome Aboard,..... You can build a gantry, or hire an extendable boom wrecker, or a back hoe/ track-hoe, or maybe a pretty stout tree branch,..... Btw,..... Don't hi-jack old threads, over 90 days old, 'n please read, 'n follow our posting rules, 'n guidelines,.....
  2. Bondo

    Trim cylinder threaded eye size and thread pitch?

    Ayuh,..... Welcome Aboard,..... I have no idea, but suggest you mike the shaft, 'n use a thread pitch gage to see what the threads are,..... You do realize, it won't trim in as far when you extend them, Right,..?? Does Sei have an answer for this question,..??
  3. Bondo

    88 omc 5.7 motor swap

    Ayuh,..... Welcome Aboard,...... As noted, the automotive Hei is a no-go, as it's not ignition protected,...... Dui makes a Hei that is,..... The go-to boat replacement ignition is the Delco Voyager system, which is reasonably inexpensive,......
  4. Bondo

    Engine Alignment tool goes in about 1/4 of the way, question.

    Ayuh,..... You should be able to see the splines in through the gimbel bearing,.....
  5. Bondo

    4.3 OMC Cobra electric choke issue

    Ayuh,..... Welcome Aboard,..... Yes, powered by the ignition circuit,....
  6. Bondo

    1984 Mercruiser 470 Ignition Switch

    Ayuh,..... Welcome Aboard,..... I've never seen a key switch, with a ground wire on it,..... Usually it's (B) battery, (I) ignition, (S) start, 'n possibly (A) accessory,.....
  7. Bondo

    alpha 1 gen 1 outdrive issue

    Ayuh,...... Sounds like it slipped outa forward as you stabbed the drive on,..... I use a bungee strap from the cav-plate, 'round the prop shaft, back to the cav-plate to hold tension on the prop shaft, to hold it in forward,....
  8. Bondo

    Mercruiser 6.2 cracked engine block from cold

    Ayuh,.... Welcome Aboard,.... My guess is, yer options are goin' to be severely limited,.....
  9. Bondo

    Mini Excavators

    Ayuh,.... If I could have just one machine to do all the things required for buildin' a homestead on raw land,.... I'd be lookin' for a TLB like a used cared for Ford 555, or Case 580, or such sized machine,....
  10. Bondo

    Happy Birthday Bondo !!!

    Ayuh,..... Had one for quite a few years now,.... plain ole chassis grease in that one,...... Got an ole pistol grip one with 2-4-C in ti, for bushing type bearings,..... Thank you to all of you,..... made it to 68, 'n still goin' strong,.... ;)
  11. Bondo

    Where are the rear motor mounts on a mercruiser 120?

    Ayuh,..... In my shop, I could have the motor bolted to a stand on the floor in under an hour,.....
  12. Bondo

    Where are the rear motor mounts on a mercruiser 120?

    Ayuh,.... 'n pull the drive off 1st,....
  13. Bondo

    1979 Sure Cast side hull questions

    Ayuh,..... Welcome Aboard,..... #1, Never heard of yer boat,.... #2, I think it was built that way,.... #3, I'd just run it, no problem,....
  14. Bondo

    Power Trim Question...

    Ayuh,..... Welcome Aboard,..... Is this an outboard, or I/O,..?? Who's outboard or I/O,..??
  15. Bondo

    Hi I need alittle help

    Ayuh,.... The spark goes from the coil tower, to the center of the distributor cap, where the rotor sends it out through the plug wire to the spark plug,....
  16. Bondo

    140 Mercruiser Fuel Filter

    Ayuh,..... Ethanol, 'n water will do that,....
  17. Bondo

    Mercruiser inboard 1980 Chris Craft Raw water cooling flowpath

    Ayuh,..... Hard to tell in yer picture, where does the in-coming water from the raw water pump go into the t-stat housing,..?? That big bar hides alot,...
  18. Bondo

    Ignition shift interrup on 1980 V8 Mercruser inboard

    Ayuh,.... It's the tension on the cable pulls the big plastic rocker which activates the switch,... It shifts, then there is no more tension on the cable, 'n the big rocker is spring driven to center, the switch opens again,..... yer picture above is missing the rest of the assembly,....
  19. Bondo

    Carb troubles

    Ayuh,..... Welcome Aboard,...... Unfortunately, you weren't successful,... Take it back apart, 'n recheck the float level, 'n make use all of the passages are clean,.... You missed a point somewhere,....
  20. Bondo

    Extra parts? Where do they go?

    Ayuh,..... Welcome Aboard,...... Hopefully the ssteel pin is still in it's holes at the top of the y-pipe,.....
Top