Search results

  1. K

    1971 StarCraft holiday

    Google Dometic straight rack cables. There might be a universal cable rack that fits your helm. The thread pitch is universal so you do not have to worry about that.
  2. K

    1971 StarCraft holiday

    Your cable looks like a Det mar . The cable and rack were usually sold as 1 piece. It looks like some company called Dometic may have bought out Det mar many years ago. You will have to buy a complete new helm/cable kit. To be sure for a correct cable length fit, measure the length of the...
  3. K

    1971 StarCraft holiday

    Most likely the cable is binding inside the tube on the inner transom plate. what color is the steering cable outer jacket? If you look closely the length of the cable is printed on the jacket. Is the helm under the panel round or straight. You will need a new cable but first it will help to...
  4. K

    Twin Solex pa44 1, volvo penta Aq151B

    Are you sure that the throttle plates are synchronized ? If one is opening more than the other it will act like that. If the carburetors are working correctly the idle mixture screws should be a 1.5 turns out from lightly seated. Any large deviation from that then the carburetor has a problem.
  5. K

    Older Ranger Inboard

    It could be either a Waukesha, Holman Moody, or even a Genuine Volvo. The main thing is it has the adapter housing, along with the external brackets for a small block Ford. As Scott said lets see some pictures.
  6. K

    120 Mercruiser I/O Trim hydraulics

    The 4“O” rings under the pump can also be obtained from a NAPA store. They have them in a box by size and can be matched up. Before you reinstall the block put a straight edge across the bolt holes, you will see that the block is distorted. Mount it in a vise and with a good file smooth it...
  7. K

    Replacing ignition on old 165hp GM inline-6

    There was a HEI that came on the last production inline 6 truck and other GMs that used the inline 6 engines. They require a solid 12 volts along with a 12gauge wire. It has a tachometer output also.
  8. K

    Replacing ignition on old 165hp GM inline-6

    The 18-5519 from sierra would be my choice. It comes with a coil and spark plug wires. Your original distributor by now has a worn out bushing and no lower bushing. The lower distributor shaft bushing in the block above the oil pump should be worn out also unless the engine was recently...
  9. K

    1997 7.4 mercruiser mpi blue water inboard

    I did not know that Merc was using Hurth transmissions. That definitley keeps it simple and uncomplicated.
  10. K

    1997 7.4 mercruiser mpi blue water inboard

    I guess it depends on the transmission to provide left and right propeller rotation. I cannot imagine both propellers turning the same rotation. Now I am curious. Does Merc have transmissions that provide L&R propeller rotation? If it was a Volvo then it is easy to have both standard...
  11. K

    1997 7.4 mercruiser mpi blue water inboard

    Wherever you go if you decide on a rebuild be very sure that they are familiar with reverse rotation engines. As well as keeping the port and starboard engines‘s parts separate.
  12. K

    454 vibrating and breaking starter bolts

    The un counter weighted balancer is probably from a small block engine that are internally balanced. A good thing that you found the problem. I had that exact engine and I remember the balancer along with the countered flywheel.
  13. K

    2003 Chris Craft Launch 25 - VolvoPenta engine replacement - need engine advice

    Check with Marine Power also Michigan Motors is a Marine Power dealer.
  14. K

    5.7 slave cylinder wiring

    The black wire may have been connected to the slave solenoid on the “I” terminal to provide a ground. Try to start the engine with the wire disconnected, if it does turn over then the wire goes somewhere else. If the slave solenoid does not engage then connect the black wire to the “I”...
  15. K

    1985 volvo penta aq 280 tilt trim limit switch

    If the trim sender is the type that has a cable going down through the transom plate and attaches to the suspension fork you are lucky it lasted this long. It has a stainless wire covered with plastic that eventually goes away and binds in the sealing grommet. You can try removing the sender...
  16. K

    Mercruiser 200 V8 Alpha 1 MR Drive

    Another place to look at is the water hose from the bell housing to the gimbal housing.
  17. K

    Installing new bellows

    The inside of the bellows is tight where the outer surface of the universal joint coupler passes through. Put some grease on the coupler and rotate the coupler with a suitable tool until the shaft engages the engine coupler, by then the drive should be able to go all the way in.
  18. K

    Selectrim-Abandon or hook back up?

    The solenoids always gave a lot of trouble. If they have 4 terminals then they are non grounded base types. They look just like automotive styles but will not work since the “I“ terminal is hot when the solenoid is triggered and since it is connected to a ground wire which burns out the...
  19. K

    Selectrim-Abandon or hook back up?

    The holders get weak and I have had a few times where the fuse would check for continuity but not passing any current and yet not showing any signs of being burned. Another problem is where they are in relation to the engine cover’s closing, the holders are supposed to be water proof but...
  20. K

    Selectrim-Abandon or hook back up?

    Just be sure that the rams are sealed and not leaking. Sometimes the cover that retains the piston will be cracked. Do not worry about travel of the rams. When the engine is back in the boat be sure that the engine does not “lean over” to one side when the rams are at the end of travel. You...
Top