Search results

  1. K

    Need Prestolite cap/rotor info

    Post a picture of your cap, rotor the distributor body and the points. Someone on the site will know what you need.
  2. K

    Bogging down

    Get A 6 gallon outboard tank and set it up where it is easy to connect to your engine. Run the boat on the regular tank until the problem starts then switch to the other tank. A very good chance the problem is in the tank suction tube internal filter.
  3. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    Yea, if the engine is a V8 then it is a 200. I thought it was a V6. After the Buick V8s then they converted to Chevy 283s then 307s.
  4. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    With the ignition on and engine not running shift to forward, try to rotate the propeller, it should lock in one direction. Next loosen the oil drain screws and see what comes out. If the lift still works that would be a miracle. If the carburetor is a 2 barrel then it is a 155 hp, a 1 barrel 150.
  5. K

    No compression with rocker arms torqued

    Most times the sender is the problem. There is a membrane inside that leaks internally, they sometime read normal on start up but after a short time they equalize internally and rear 0.
  6. K

    Rescued 69 Evinrude Rogue with stringer need beginner tips

    Those Evinrude/Johnson boats were very well built and quality was good. Unfortunately they were expensive and priced themselves where OMC most likely lost $. If your boat is a pre 68 model original drive parts are impossible to find. While the engine may still be in good condition that is where...
  7. K

    Remote sticks when going into reverse, but only when in water.

    With the engine off shift into reverse full throttle, the roller should still be in the center of the “V”. If not then look for the ACHRIS tutorial video on this site which should help you.
  8. K

    Volvo Penta Ford help

    Post some picture. That will be some help to figure what you have.
  9. K

    Remote sticks when going into reverse, but only when in water.

    Did you disconnect the shift interrupter switch wire?
  10. K

    2003 FW freedom 180 3.0 recent first start since October 2022.

    Post a picture of the carburetor. Then we may be able to help.
  11. K

    No compression with rocker arms torqued

    If the marks were still in line you are good.
  12. K

    No compression with rocker arms torqued

    If the picture of the timing chain is your engine you have it right so that is not the problem.
  13. K

    Trim oil leak into bilge

    Once the trim block is down you will see that it is real easy to feed the line through the hole. Wrap tape around the open end before pushing or pulling the line through, there is a lot of dirt in that area.
  14. K

    Trim oil leak into bilge

    To get to the leaking line the trim block under the gimbal housing has to come down. Remove the 2 lock nuts and you may have to pry on it but it will come down. A 3/8” flare nut wrench should loosen the lines up. The most forward line is the high pressure “up” line. If there is no source for...
  15. K

    No compression with rocker arms torqued

    Look at my post #11. Also you can get more information if you google “converting a MK5 to adjustable rocker arms”. You just need the stud and locknut kit or the “poly lock” style which are better. I do not feel that there is a valve problem.
  16. K

    Mercruiser 470 - Cam Seals Repair Questions

    The sealant should work. With some research you might be able to locate a sleeve that is long enough to cover the whole area to be repaired.
  17. K

    Steering shaft removal

    He needs the picture of the intermediate housing if you can post it Doc.
  18. K

    No compression with rocker arms torqued

    With the rocker arms removed just look closely at the top of the valve retainers to see if any are higher than the others, that will tell if any valves are tuliped. Do not start trying different pushrods. Get the adjustable stud kit and set them @ 3/4 from the point where there is no slack but...
  19. K

    Merc 3.0 Overheating

    Most times the riser is what causes water flow problems rather than the manifold body. If you have a water hose supply try connecting the hose to the manifold inlet. The water should free flow through it. A leaking head gasket builds up enough pressure where it overcomes the pressure from the...
  20. K

    Mercruiser 470 - Cam Seals Repair Questions

    As long as there is the proper ratio of coolant in the engine just remove the end caps on the heat exchanger and the plug on the exhaust riser. That will drain the raw water. Store it with the drive down. Put a thin film of silicone on the shaft before pressing the sleeves on, it acts as a...
Top