Search results

  1. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    2006 225 4stroke. Starts right up but runs crappy for about 10-15 min. Won't accelerate without missing. Then when warm it smooths out and you can give it gas and it runs good. Fairly new plugs, 175-180# compression. Started and pulled each plug wire and each cyl. would drop until the wire was...
  2. jerryjerry05

    Seadoo GTX 4 tec

    Is there a Seadoo repair forum other than this, or just ask here? 2004 seadoo gtx 4 stroke supercharged bombardier(heck of a name) Have a pair of them, they sat for 4-5 years and one doesn't want to turn over. New batteries, one just clicks and the starter engages but only groans and when the...
  3. jerryjerry05

    1999 Johnson T@T Airbound?

    1999 225 Johnson Trying to fix the T@T Might be airbound? Bad motor, replaced, added oil and motor works but won't go up or down. The release works or should I say it turns. Thanks
  4. jerryjerry05

    2005 90hp Yam no spark.

    2005 90TLRD 1017108 Guy calls and says his motor has no spark. What's the first thing I should be looking for? I haven't looked at it yet, probably tomorrow. I have a DVA Thanks
  5. jerryjerry05

    150 Evinrude Ficht 2004

    Twin 150 Ficht, both only go to 2500 and then cut out. Any suggestions or ideas? Any other repair forums or places ? The only place in the treasure coast area keeps putting the owner off, first appointment was Jan 10 then next week and again next week. ANY HELP would be appreciated. The owner...
  6. jerryjerry05

    Trim tabs.??

    19ft center console 115Yam 4stroke. QUESTION: is a 19ft too small for trim tabs and if not what size tabs?? Thanks
  7. jerryjerry05

    Water in cylinders

    1986 200hp Starts and runs then gets water in the 3 cyl on the right(maybe the left???) That's all the info the owner told me. ????
  8. jerryjerry05

    Twin 150 Fichts won't rev past 2500

    Twin 150 Evinrude Ficht. Starboard starts and idles fair. Good compression. The port doesn't want to idle well at all unless the balls squeezed. The check engine light comes on both motors and won't rev past 2500 rpm. New hoses/squeeze balls and cleaned oil tanks new squeezies. What would cause...
  9. jerryjerry05

    Yamaha 2004 150 carb

    The motor runs great (mostely) , new impeller, thermo's,plugs,etc Running for about 1 mi. and then alarm sounds off and goes into limp mode(?) Back to idle and then it can be ran up again. Not overheating(tested) pretty sure the oil system is the problem. Cleaned both tanks and got the sludge...
  10. jerryjerry05

    Ficht leaks fuel.

    Johnson 150 Ficht. Not sure of the year??? # on the silver plug 4886732 As you(me) squeeze the bulb fuel squirts out the top cyl or hole for the top cyl. see pic by the #1 What's behind there that lets fuel out? THANKS When you run it runs but not as good as the second motor.
  11. jerryjerry05

    WATER!!

    1986 200 Mercury. My customer said he thinks there might be water in the motor??? He's right. The stbd. bank of cyl. was full and had hydro locked the motor. Got it freed up and running good on the hose. He put it in the water and it did it again. Same 3 cyl. on stbd. bank. Any ideas??? Thanks
  12. jerryjerry05

    Changing ignition systems???

    Working on a 1994 25hp Mercury. Somewhere along the line I got some info that there might be an ignition change from the old SWITCHBOX ASSEMBLY *{(Jet 20)}* 18495A30 To SWITCHBOX ASSEMBLY *{(20/25) SN# USA-0G438000/BEL-9927000 Up}* 7452A19 Two different packs and I guess the...
  13. jerryjerry05

    Tach output from the motor

    1986 200 Mercury The wiring in the boat was a big ol pile of spaghetti!! I finally got all the wires back to where they were supposed to go( I think :) ) How do you check the motor to see if the signal to the tach is working? I turn the key and the digital readout (bottom face of the tach)comes...
  14. jerryjerry05

    Mercury slowing down

    1995 Mercury 75 hp. 17ft.Ranger Alum. bass boat. I don't know how to set the timing and don't have a manual for the motor. The motor seem to runs good and hitting on all 3 cyl, The linkage/throttle is advanced as far as it can go. Yet the most it gets is 4100 rpm's and 30mph. at wide open and...
  15. jerryjerry05

    Oil recirc lines diagrams?

    I believe it's a 97 30hp.The ID tag's long gone:( The bottom of the intake is a tiny hose barb, I think it's a recirc oil hose, maybe it's recirc fuel line? Anyone have a diagram for the hoses on this motor? Thanks
  16. jerryjerry05

    Yamaha outboard value.

    It's a 2004 15 hp 2stroke. Very little use, been setting for the last 12 years that I know of. I got it running about 5-6 years ago and the owner put it right back in the shed after his son used it for a weekend. I know the amount of time means nothing but the looks do, The cover is...
  17. jerryjerry05

    Free manual link.

    Lost !! I lost the link to the free manuals on line. Can someone post it?
  18. jerryjerry05

    Transom clamp removal

    2000 115 Johnson. The clamps have been soaked in salt water for years. The snap rings were hard to remove(painted over) and the pins are frozen in place. I tried a propane torch to remove the tilt ram pin, didn't budge. I have a acetylene torch but want to make sure I'm not missing something...
  19. jerryjerry05

    High idle

    1999 Evinrude.Carb model. Serial # coming soon. The comp is good, good spark. The rpm's at idle are 2-3k if not more. The linkage is set so the throttle pickup point is open. It won't go anywhere to let the idle down. How/what do I do to bring the idle down? Seems as though there's a new...
  20. jerryjerry05

    Shift rod measurement

    Looked up the Johnson/Evinrude shift height measurements. I found the link but it goes to something about an older Chrysler ??? I found the right measurement.
Top