Search results

  1. jerryjerry05

    1975 chrysler 4.9 wont start

    Clean the carb? Unscrew the tiny screw on the top of the gas cap? Turn the gas on? When it's on remove the hose and see if it flows to the carb. Try removing the float bowl on the carb. Spray WD-40 or any penetrating oil on the base making sure the spray gets on the top of the bowl and the...
  2. jerryjerry05

    what is this part and where to get one?

    How about some lubrication? WD-40 can work miracles.
  3. jerryjerry05

    Force 125 88’ won’t run

    The motor can start even if the timing is off as much as 15-20d. That screw, not bad enough to make it not start. Check for TDC. Told you how on the other post.
  4. jerryjerry05

    1975 chrysler 4.9 wont start

    This or one the right size goes in the groove on the top of the crank shaft. Then the flywheel fits over the key with the slot cut in the taper. This is the part# but it might be hard finding. MAGNETO KEY F12150 You can make a key fit if all else fails. it needs to be a tight fit or it can...
  5. jerryjerry05

    Merc 40 Force - Takes forever to start

    Sounds like the primer is bad?? Cover off, key on, have someone push in the key as you touch the primer, you should feel a click. No click??? Test light, same procedure but use the test light on the wire. This should light the light. No light? Then the key switch might be faulty. Key switch: WD...
  6. jerryjerry05

    1990 spectrum blue fin 50hp force control cables

    They might work? But if they are used, I wouldn't put them on my boat. Ebay this "Morse 33 shift cable 12ft." Look through the cables they have. If the add says Morse or 33 they should be ok. Some are from China and can take up to 2 months to get.
  7. jerryjerry05

    what is this part and where to get one?

    So when you pull the cord it doesn't lift the white thing? Couple more pics from different angles?
  8. jerryjerry05

    88' Force 85hp lower unit oil viscosity

    Yes then fill from the vent till it comes back out the fill. Repeat until it won't take anymore.
  9. jerryjerry05

    1990 spectrum blue fin 50hp force control cables

    I get my replacements on Ebay. Easy to change. Take pics of the shifter as you attempt it.
  10. jerryjerry05

    Force 125 88’ won’t run

    If it lights up on each plug?? then you have spark. That broken gasket: I wouldn't worry about it right now, it's probably not all the way through and just the corner. The part: called a Dog Bone. It's part of the fuel recirculation system. Take it apart, it has reed valves and screens to catch...
  11. jerryjerry05

    what is this part and where to get one?

    Needs a better picture. The white thing: GEAR, STARTER PINION F487674 that's #2 in the picture. Your pic only shows #2 and there's more that we can't see.
  12. jerryjerry05

    Force 125 88’ won’t run

    GASKET, FUEL PUMP F438760 DIAPHRAGM, FUEL PUMP F438747 change them. GASKET, TRANSFER COVER F40223 This gasket could be the problem. 4 of them. Cheaper on Ebay "27-820500A3 Transfer Port Cover Gasket Kit Mercury Force 40-50HP Outboards"
  13. jerryjerry05

    Do I need to do timing after stator replacement

    Read the rules? This post is 11 years old. If you don't unhook the trigger when changing the stator? then no need to retime.
  14. jerryjerry05

    Thermostat and pissing issue

    This site, it used to have parts diagrams for your motor??? Buy from here, if not then Ebay is a good place and often cheaper. Now you gotta have the part #s from somewhere ?? Boats.net has diagrams. SUPERSEDED BY 819377 - GASKET $2.45Quantity: 1 WASHER $6.35Quantity: 1 THERMOSTAT 54C (130F)...
  15. jerryjerry05

    Control rod seal and copper ring for drive shaft and boot

    The missing ring?? No biggie, just lube the splines and slide the boot over them. No grease on top of the shaft. There's a slotted screw on the side of the nosecone, DON'T remove as it's a pivot point and can be a B%$#H to replace. If you do remove it then the seals a lot easier to get at.
  16. jerryjerry05

    Force 125 Propeller spins but the boat doesn't move

    Can bind right where the shift shaft enters the lower unit.
  17. jerryjerry05

    Force 125 88’ won’t run

    Don't make it backfire!!! This can cause way more problems than you can imagine. FIRST: do a compression and spark test, post the results?? How is the fuel system set up? Portable tank? built in tank? How did you mix the gas/oil? Pull the plugs and compare them then post a pic of them in order...
  18. jerryjerry05

    Gas Leaking from exhaust while priming bulb.. ?

    If you can hook it up?? Then it should work. They all use the same system just the mount is different.
  19. jerryjerry05

    1990 force 50hp driveshaft spline boot and keeper

    Boot and retainer not really needed. BUT if you run in salt water it's possible the corrosion caused by the salt water can make the connection a permanent one.
  20. jerryjerry05

    ‘92 Force 40 Shift Shaft Seal

    The driveshaft, after water pump removal should pull out. Then same procedure, pry or use the seal removal tool. Both methods can score the soft alum. so be very careful.
View older results
Top