Search results

  1. jerryjerry05

    1987 force 125 plug wire question

    Yea, pictures please, show us what you have?
  2. jerryjerry05

    125 force cant find serial & model numbers.

    What color is the motor? White or Black?
  3. jerryjerry05

    1995 Force 120 Thrust Washer confusion

    Pictures will help: pic of the prop and thrust hub on the motor. Pics of everything. Is the prop OEM? or aftermarket?
  4. jerryjerry05

    Force 85 HP tilt/trim model no.

    If you look at the first 5-6 posts in the Force forum you'll find a bunch of info on the T@T The pic that Topgun posted shows 1 of 2 different valves. The second (older style) is held in by snap rings. HOPE that yours is the newer style, much easier to work on. Remember: there's nothing in the...
  5. jerryjerry05

    '88 85hp vs '85 and '86 125hp compatibility

    Nordin said it. The test(you) was faulty, bad gauge. You can change the packs and coils, you'll need to cut the ends off and use butt connectors. They say the blue and black shouldn't be paired together but I never had a problem. The main difference in the 85/125 is the extra cylinder. They use...
  6. jerryjerry05

    125 force cant find serial & model numbers.

    Very rare that all 4 coils go bad. In fact since 1986 I have seen only 1 coil that was bad. The 125 , Blue paint used the same pack and coils. as the 120 from 1987 to 1993 Standard ignition has cheaper prices. outboardignitiondotcom has test procedures. Good luck, put up your own post and add as...
  7. jerryjerry05

    1993 pontoon boat with a 40 hp Force.

    MAYBE??? It sounds like the primer/choke might be defective? Just because you hear a click doesn't mean it's working. The "click" is the primer opening and allowing a quick shot of fuel to enrich the system and making it easier to start. The primer has a diaphragm that can go bad and leak...
  8. jerryjerry05

    Force 85 HP tilt/trim model no.

    The 1989 T@T didn't come with a model or serial number it came as part of the engine package. If the "new" pump isn't working right??? Send it BACK. There's nothing you can do to it to fix it. NOTHING!! The only thing you can do to one of these pumps is to change the tiny red seals, these seals...
  9. jerryjerry05

    Force 70hp New trim motor

    IF the pump is new?? Then it's probably bad. Famous Chinese JUNK!!! What system do you have? Pictures?? They made 4-5 different systems and procedures for filling are many.
  10. jerryjerry05

    1995 Force 120 no water pumping through powerhead

    No such thing as salt deposits washing away. There are some things that will help dissolve them. Big bucket: couple gallons of vinegar and box of baking soda. Run the mix through and let it set. Run it and repeat 4-5 times. That might help, maybe not. The one sure way is take it apart and use a...
  11. jerryjerry05

    1993 Force 50hp 2cyl 2 stroke What in the Jerry Riggin'?

    Looks like someone adapted a newer Mercury ignition. outboardignition.com for testing the systems. By the way: it's Jury Rigged, Not Jerry
  12. jerryjerry05

    1995 Force 120 no water pumping through powerhead

    Pull the lower unit. The impeller shouldn't be soft and pliant. Replace it. Everyone I have seen(hundreds) is stiff and not easy to install. Old piece of hose, cut off end and run the hose up the pickup tube and run it. Running in a bucket: the bucket needs to be DEEEP at least 4" over the...
  13. jerryjerry05

    Force 5hp (1990) no telltale?

    On the mid section is a lump with 2(?) holes that the water should be coming out. Very TINY!!! wasps get into the holes and make nests. Small piece of wire up inside the hole and see if the nests/babies comes out. Reverse: it has it, just turn it around and then push the gear lever down.
  14. jerryjerry05

    Merc 40 Force - Takes forever to start

    Like Racerone suggested, check/rebuild or just clean it out. Makes a huge difference in the way it works and adds years to it's life. The brushes sluff off and they leave carbon bits in the bottom and that can short out the works.
  15. jerryjerry05

    Shifter fnr adjustment on a Force/ Mercury 125

    Once it's back together and before the oil, do a pressure test.
  16. jerryjerry05

    Adjust all 3 carbs at once or seperate ?

    You can set it anyway you like. Then do the starting fluid test: spray around the intake side and if the spray makes any difference?? Fix it as an air leak can kill your motor. THEN!! it needs to be fine tuned in the water and in gear.
  17. jerryjerry05

    Voltage regulator

    If I needed to buy a voltage reg??? outboardignition.com Force Regulator Item#194-5279 $190.
  18. jerryjerry05

    Force Vs Johnson

    The 85/90 Force were said to have the best power to weight rating for that motor. The rest is my opinion. The T@T on the Force is the weak point. But can easily be fixed with a few wrenches. They BOTH are hard on fuel. The Johnson electronics seem to last longer. Lower unit, both are about the...
  19. jerryjerry05

    what is this part and where to get one?

    IT's possible the spring inside the starter is broken or has come unwound?? Find a video and see if you can tighten the spring.
  20. jerryjerry05

    Force 125 88’ won’t run

    The first 5-6 posts cover help and tricks for fixing your motor. Look for the link and sync The way it died: it looks like the rod between the carbs might be set wrong(maybe)??
Top