Search results

  1. jerryjerry05

    1983 Force 50 hp Parts

    Look no further, this site sells parts!!!! Topgun's advivse is real good too. I buy almost everything from ebay. boats.net has parts and diagrams.
  2. jerryjerry05

    Force 120

    IF??? the rpm's go up but the speed doesn't increase?? the prop hub might be spun. Check the forum/web on how to test the hub for slippage.
  3. jerryjerry05

    50HP Replaced impeller and thermostat. No water flowing. Where to look?

    Using muffs? Some muffs don't always work right, tape it in place.
  4. jerryjerry05

    Force 120

    Gotta figure out the rpm's at wide open??? No tach?? Get a Tiny Tach about 20$-25$ Your motor should run at 53-5500 RPM's Post that info and we can help you get the speed. The speedo working right? You should be able to run at 40-45 mph.
  5. jerryjerry05

    Lovely but What?

    The ignition switch OEM is over $100 They used 2, one is the long barrel, the other is the short. A better pic will help. Sometimes the starter will have the part numer on it and doing some research you can figure out the rest of the info you need. Bayliner is still selling/making boats. If...
  6. jerryjerry05

    Adding Tilt/Trim system 89 bayliner

    The harness and relays is so the electric motor doesn't get the wires too hot. And yes hook the leads to the battery and see if it works?? 99% of the time T@T failure is due to the bad connection on the relays. Take them apart and clean the contacts making sure they make good contact. A simple...
  7. jerryjerry05

    Stuck check valve…

    The best bet is upgrade to a newer pump. The older pump/valves were pressed in. They hardly ever went bad. One time in 40 years did I see a valve go bad. It fell apart but still worked.
  8. jerryjerry05

    Lovely but What?

    That boat , worked on hundreds of them, is a Bayliner and that model was made in a factory in Washington state. The paint job on the motor and hull shows it's a 1987, the hull ID # probably shows it too. The motor should have a sticker on the transom clamp that has the model and serial number...
  9. jerryjerry05

    1996 force 75 trim guage

    Those models didn't have a sending unit. But they installed a gauge anyway. :(
  10. jerryjerry05

    Here's one for the books!!

    2014 Yam115 4stroke. The aftermarket Sierra developed a pin hole leak and saturated the lower half of the motor, including the starter. Went to change the filter and clean the oil. Took the starter and all the electrical connections apart and reassembled everything. Went to start it and huge...
  11. jerryjerry05

    Force 70 hp questions.

    Force didn't always have a freeze plug. Look on the starter for the year? if it hasn't been changed it should be on there. ALso there might be a foundry stamp under the pack/coil assy. and under the bottom carb. Round circle with the year in the center. The T@T wires were/are solid blue(up) and...
  12. jerryjerry05

    MISSING!!!!!

    Thanks
  13. jerryjerry05

    MISSING!!!!!

    A post in the repair section in the first posts is missing. The carb link and synk is MISSING!! The one by FrankA is gone. It goes to a post about fixing a 454 Mercruiser. HELP!!!!
  14. jerryjerry05

    Startup backfire

    Post is 9 years old.
  15. jerryjerry05

    1990 force 90 hp trim pump kit?

    RRitt's daughter continued the business after he passed, not sure she will still be in business. She was onEbay under his name. RRitt
  16. jerryjerry05

    Force 85hp Backfiring Out Exhaust

    Post is 15 years old. Maybe start another with good details?? Backfiring can be: too much gas an air leak timing off and much more
  17. jerryjerry05

    1990 force 90 hp trim pump kit?

    I found buying the new pump the best option. BUT!!! be careful where you buy??? The real cheapo's can and usually fail right out of the box.
  18. jerryjerry05

    1990 force 90 hp trim pump kit?

    Thanks Topgun. There you go, problem solved. One hint be EXTREMELY careful when taking the valves apart, I've never found anyplace that sells any of the parts except the seal.
  19. jerryjerry05

    '88 Force 15 "Where's the thermostat?"

    I'm not surprised anymore on what people do or don't do. From what you said?? it sounded like you were going to reuse it.
  20. jerryjerry05

    1990 force 90 hp trim pump kit?

    I thought someone had put a link to the repair kit that fixes the shuttle valve. ANYONE know the part # or where to buy the tiny little seals? I know Granger sells them. If you can't get them I might have a couple in my spare parts bin.
Top