Search results

  1. jerryjerry05

    1991 force 150 hp water pump replacement

    WATER PUMP KIT FK1204-1 Most times all you need is an impeller IMPELLER-Water Pump F694065 about 35$ This site sells parts. From the part#...
  2. jerryjerry05

    Tips for Re-Installing a Flywheel?

    A spot of superglue?
  3. jerryjerry05

    Help with 1974 chrysler 1057hf

    Nordin usually answers questions on these older motors? I don't have that much experience on these older Chryslers.
  4. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    Bosco, none of your business what I do. You don't want to help??? then don't read any of my posts and keep your opinions to yourself. Nothing good to add?? add NOTHING!!
  5. jerryjerry05

    Help with 1974 chrysler 1057hf

    The following links are for some repair/tests. They might work on your setup?? https://www.outboardignition.com/support/115-3301.pdf / Powerpack https://www.outboardignition.com/support/155-1450.pdf / Rectifier https://www.outboardignition.com/support/182-5475.pdf /Coil...
  6. jerryjerry05

    125 Force Outboard won’t achieve full power

    That might be part of the problem???
  7. jerryjerry05

    Help with 1974 chrysler 1057hf

    What ignition system?? Distributor? Magnapower? The newer ignitions(your repair page) that uses power packs and you probably don't have that system. The stator on the older systems charged the battery, the newer systems the stator gone bad could kill spark to the system. The newer system, the...
  8. jerryjerry05

    Best gasoline octane for old Chrysler Outboards

    What I would do: use the 87 with 10% Ethanol. Add Ethanol stabilizer if the boat "might" set for a while??? Otherwise I just ran pump gas, usually WallyWorld gas, and kept the tank full after using. Try t keep it out of the sun. The biggest problem was the rubber hoses melted from the Ethanol...
  9. jerryjerry05

    89 force 50 lift ring

    Took the lift ring to Home Depot. They had nothing to match the threads to. The parts list says 3/4-16 F-1968 part# It's the same for the 50-85-120 125- 150
  10. jerryjerry05

    2003 lx225 OX66 knocking sound

    Compression test? Bore scope/camera?
  11. jerryjerry05

    89 force 50 lift ring

    In have one. If you don't get an answer, I'll take it to Home Depot and get the threads measured and post on here tomorrow.
  12. jerryjerry05

    89 force 50 lift ring

    I can't find the part# for the lift ring. The 50 needs a smaller lift ring than the bigger motors. I used piece of 1 1/4x 1/8 x 4"flat stock. Drilled 2, 3/4" hole 1/2" from the end and then bent it 90d. Then removed the flywheel nut, installed the new lift bracket, replaced the nut, then lifted...
  13. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    The thermo's are used in conjunction with thermo switches. I don't have the manual, that's why I ask here. Anyone have test procedures and values for the thermo switch's? Thanks
  14. jerryjerry05

    Help Pulling 1992 90hp Force out of Jetstar

    Look on the jetski forum? Google repair forums?
  15. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    Yam thermo setups are different than regular thermos . They're hooked to a thermo switch assy. Thought there might be some special tests for that part??? You do know how to test them don't you?
  16. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    No didn't look at the thermo's. What to check on them? What tests?
  17. jerryjerry05

    Yamaha 2005 F90TLR Flywheel Torque

    I think 85-90#
  18. jerryjerry05

    2006 225 4stroke runs poor until warmed up.

    2006 225 4stroke. Starts right up but runs crappy for about 10-15 min. Won't accelerate without missing. Then when warm it smooths out and you can give it gas and it runs good. Fairly new plugs, 175-180# compression. Started and pulled each plug wire and each cyl. would drop until the wire was...
  19. jerryjerry05

    Check for play in VP SX-A outdrive?

    Turning the drive left to right play: None Lifting up and down: none to very little. Draw on the battery: maybe the radio? or depth finder? They both can draw even when turned off. Test: undo the ground at the battery, test light installed on the battery lug and the end of the cable. Is the...
  20. jerryjerry05

    1990 150hp force trim & tilt

    Not o rings. This link has pics of the parts. You need pic#93 Working on the pump itself: they don't usually go bad. ANY!!! attempt to "adjust" the pump usually destroys it. About the only thing you can service is the check valve. Be VERY careful when taking apart, soft aluminum...
Top