Search results

  1. jerryjerry05

    1973 Chrysler 6 HP Two Stroke

    Flipping a seal: If??? you think the seals leaking and don't have a replacement then sometimes flipping it over and reinstalling, can help stop it from leaking. It works in a pinch. The wear surface usually ends up in a new spot and can stop the leak. Desperate measures.
  2. jerryjerry05

    1996 Force 40HP suddenly died, wont start.

    Test it. Squeeze the ball to prime the system. Turn the motor over a couple of revolutions. Then unhook the yellow hose at the primer and pinch off the hose. Then have someone turn the key and activate the primer. There should be a shot of fuel from the primer when the key is pushed in. If...
  3. jerryjerry05

    1989 85 HP Force neutral safety switch help!

    Two tiny allen head screws. Why remove it? It's there for safety. You need to hook the two wires together or the motor won't start.
  4. jerryjerry05

    1996 Force 40HP suddenly died, wont start.

    Plugs aren't the problem. I could put lawnmower plugs in there and the same thing would happen. Test the alarm system for overheating, then check the diaphragm in the fuel pump. The primer has a tiny hose that goes to the side or bottom of the carb, pinch that off after it starts. The primer has...
  5. jerryjerry05

    Can't get flywheel off!!

    Maybe it was the plugs that showed weak spark? I always try to get someone to hold it when I'm trying to get spark. Then I can tell how strong the spark is by how loud they scream. :) Big stick or heavy insulated screwdriver, hold the plug against the block and see how big the spark is or get a...
  6. jerryjerry05

    1973 Chrysler 6 HP Two Stroke

    Flip turning over. Shimming: adding metal shims to lift the seal s it rides on a different spt.
  7. jerryjerry05

    Pontoon sitting for over 10 years

    Probably made after 95 The Trim@Tilt is under/inside the transom clamps, that shows Mercury parts. Mercury used their stuff after 94. Rust cylinders??? If the motor turns over??? Then rust shouldn't be a problem. Look for posts about waking up a sleeping motor, or one that's been winterized or...
  8. jerryjerry05

    Can't get flywheel off!!

    Before you damage anything: outboardignitiondotcom has test procedures for your motor. Test it and then figure out the problem. Then if you want to remove the flywheel?? get a BIG 3 jaw puller and try that. In some cases the flywheel just about welds itself to the crank, then you might need an...
  9. jerryjerry05

    1989 85hp force outboard no start issues

    What we working on here? Force or Evinrude? You should start your own thread, and in the right forum.
  10. jerryjerry05

    1996 Force 40HP suddenly died, wont start.

    The plug they sold you was too long, but Champion says they are a replacement. The QL76V are the right one. But I don't think the plugs are the problem :( Sounds like it's overheating or the fuel pump is bad??
  11. jerryjerry05

    89 force 125 leaking fuel from carbs

    IF??? Ethanol was ever used it could be the problem??? Ethanol deteriorates the inside of the hose and delaminates the inner lining. Had a hose swell and shut off the flow of fuel, looked like a couple of curly pigs tails, didn't leak but stopped the fuel from flowing.
  12. jerryjerry05

    1973 Chrysler 6 HP Two Stroke

    You can try Franz Marine (not sure they ship to Canada?? ) The oldest I can find is 1976 6hp. They made two different lengths, most were the shorter ones, post a pic of the lower. It's probably the same as the 73"maybe" What's leaking and needs repaired? Sometimes the drive shaft gets a groove...
  13. jerryjerry05

    1989 85hp force outboard no start issues

    Gold /brass cylinder.
  14. jerryjerry05

    1995 120hp Force CDI wiring diagram help!!!!

    This is the part# for your motor. Google or ebay they range from 25-250$ CDI makes a good one. Try to stay away from the Chinese JUNK. REGULATOR ASSEMBLY, VOLTAGE 883071A1
  15. jerryjerry05

    1995 Bayliner Capri 1800ls force 120hp temperature sensor? Help

    It might go into the harness, orange lead??
  16. jerryjerry05

    89 force 125 leaking fuel from carbs

    Install a filter between the pump and the carbs. Fram G2 G3 G12 one of these will work and it's clear so you can see if there's any junk in the system? Dry float bowls? needle/seat dirty, hose bad?
  17. jerryjerry05

    Force 85 Control Operation

    The magnet? it's one continuous magnet that fits inside the flywheel. They do come loose but the motor won't start if it's loose. Had one 88/85 that wouldn't start unless it was tilted all the way up and the choke was used as you turn the motor over, after it started, there was no problem the...
  18. jerryjerry05

    Cyl Head

    The 30 year old motor should have the same comp readings as a new motor. Is it 95 on 1 cyl. or all 3? Does it run? All 3 low?, that shows the test was done wrong or the gauge is bad? It really takes a lot to warp a head so bad it won't work.
  19. jerryjerry05

    89 force 125 leaking fuel from carbs

    The second pic's hole: fuel from that shows the floats not set right or the needle/seat is defective??? or dirty???
  20. jerryjerry05

    Compatible parts motor

    The pack is designed to fire 2 cylinders. There's a blocking diode in there so you can have spark on one but not the other. Sometimes no spark on one is the stator. Try swapping the packs around and see if the no fire follows the change?
Top