Search results

  1. jerryjerry05

    Lack of power

    IF?? you suspect the pack??? then the only way to test is to swap the packs around and see if the no spark follows the pack. The no fire on #2 is usually the stator or the trigger. The trigger wires are very thin and can break under the shrinkwrap on the connector. I replace them all just in...
  2. jerryjerry05

    #4 cyl no fuel

    I don't think any Chryslers except the 50hp or lower used the #4 or bottom piston to run the fuel pump. Usually #2 on a 3cyl. or #3 on a 4cyl. Some bigger 140/150 could have 2 pumps utilizing #2 #3 cyl.
  3. jerryjerry05

    Bad plug wire- 89 force 85hp

    MAYBE??? the tach is set wrong? Look at the back and see where the black arrow is set?? But a 1000rpm drop could be a coil, stator, diaphragm etc.
  4. jerryjerry05

    Vp aq270

    Stalling: what's the rpm's at idle. 800
  5. jerryjerry05

    Volvo Penta aq125a grinding noise

    No gimbal bearing, they have a drive shaft bearing. Lot different that the Gimbal replacement. The V-8 drive shaft replacement is way harder to replace than the 4cyl.
  6. jerryjerry05

    Vp aq125a aq270

    These 125/130 Volvo's need the factory prop for best performance. These 125's need the VOLVO prop. The aftermarket ones are ok for the bigger motors not the 4cyl. Volvo's . Prop story: one of my friends had a 22ft. with a 125 He asked me to look at it as he was having trouble with acceleration...
  7. jerryjerry05

    Bad plug wire- 89 force 85hp

    The wrong prop can drop the rpm's a lot.
  8. jerryjerry05

    Carb leaking gas from top two holes 1989 85hp

    I'll look through my stuff today.
  9. jerryjerry05

    Carb leaking gas from top two holes 1989 85hp

    The kit, be real careful when trying to "fix" or install any of these parts. Some kits have a seat in them and some carbs, the seat won't come out??
  10. jerryjerry05

    Proper Fuel water separator for a 125 ho Force

    ANY one will work, the ones with the clear bowl will make you happy!! Just finding a location will be tough?? Then install a small particle filter between the pump and the carbs. Fram G-2 G-3 G-12 works well.
  11. jerryjerry05

    Starter and choke issue

    The shaft or armature bends from excessive use. Also if the bottom mounting bracket is missing it leads to bent a shaft. A tiny bit of oil or thin grease on the worm gear after cleaning might help don't get too much on it or the rubber in the bendix slips and is useless.. These starters are easy...
  12. jerryjerry05

    Help!! 15hp Montgomery Ward Sea King by Chrysler Propeller

    DON"T stop there contact them in person.
  13. jerryjerry05

    Vp aq270

    These 125's need the VOLVO prop. The aftermarket ones are ok for the bigger motors not the 4cyl. Volvo's No way to add power trim/tilt unless you change the transom brackets.That would be a HUGE job if you had the T@T from another motor. Prop story: one of my friends had a 22ft. with a 125 He...
  14. jerryjerry05

    Volvo Penta aq125a grinding noise

    http://www.volvopentastore.com/mall/image/view/7/8/7464_4.png This is a parts breakdown for the 270 drive. Your lucky as if the motor was a V-8 you'd have to pull the motor to do the service :)
  15. jerryjerry05

    Volvo Penta aq125a grinding noise

    You posted: maybe primary drive bearing and bell housing bearings ? .. I'd pull the top of the drive and inspect the drive shaft. The 125 has 1 bearing and that can be serviced from the outside. On the top/back of the bell housing is a grease fitting that most people don't utilize or even know...
  16. jerryjerry05

    Bad plug wire- 89 force 85hp

    If it's an 89 you can just about bet the wire's bad. :( I thought the plug wires were part of the coil and couldn't be replaced???? Post a pic?? I've changed the plug boot and covered the wire with double shrink wrap and liquid electric tape(actually worked)
  17. jerryjerry05

    120HP Force being smothered on exhaust fumes at idle

    I've learned a few tricks over time.
  18. jerryjerry05

    Lack of power

    The linkage set right? Make sure both carbs butterflies move at the same time?
  19. jerryjerry05

    Carb leaking gas from top two holes 1989 85hp

    I'll look in my stuff? Post a pic of the needle next to a ruler.
  20. jerryjerry05

    Tilt trim switch wiring

    Put on a pic of the needle next to a ruler. I'll see if I have the right one in my stuff???? It's at 64 posts, the last are about carb stuff, might be time to start another thread?? OOOPS!! I see you already did that. :(
Top