Search results

  1. jerryjerry05

    Please help looking at a boat tomorrow

    ANYTHING but an OMC Cobra
  2. jerryjerry05

    '95 Force 120 - bottom cylinder not firing

    This works or one like it from Auto Zone
  3. jerryjerry05

    1964 45hp Sea King

    Sell it for parts if you can???? Or aluminum scrap?
  4. jerryjerry05

    Force piston rings

    The 87 35 was made in 6 different models, all 6 used the same ring set The parts are NLA from the factory but can be found if you look around, I found them on ebay, 114659905379 look up this part quick as it cheap and won't last long. There is a THEIF asking 75$ for a used set so be careful...
  5. jerryjerry05

    Tilt Cylinders Leaking

    That's the color of the pump/housing/motor itself.. Before 87 they were white and different from the blue.
  6. jerryjerry05

    Rebuilding 1991 120 lower unit

    Guess I needed to look closer to the dates???
  7. jerryjerry05

    Tilt Cylinders Leaking

    Buy what ever you can afford??? The Yamaha and Mercury oils provide better protection and won't breakdown as fast with water intrusion. Amzoil is good but expensive. Myself I've used Walmart gear oil, that's in MY motors. I use the good stuff for my customers. The most important thing: CHECK THE...
  8. jerryjerry05

    Crank no start 4.3, wiring diagram?

    You need a factory manual, Seloc probably won't have what you need. Try opening this, it has Volvo links. http://www.boatinfo.no/lib/library.html http://www.boatinfo.no/lib/volvo/manuals/43abcde.html
  9. jerryjerry05

    Force 125 lacking power

    Gaps??? .010-.020 ?? That's acceptable.
  10. jerryjerry05

    Smoke coming from starter solenoid

    You can probably use the new solenoid but you have it wired wrong. The new one, the base might need grounding? Get a factory service manual, find the wiring diagram and rewire.
  11. jerryjerry05

    Tilt Cylinders Leaking

    The blue Prestolite didn't have a grease shield/ wiper that's seen in your picture.
  12. jerryjerry05

    Force 125 lacking power

    If it's been ran in salt water? then I'd think about changing the head gasket. The bolts might be hard to remove?? the corrosion on the bolts can make it hard to remove, take your time or you'll twist the heads off the bolts. If the reeds have minor gaps?? then they'll be ok. They're designed...
  13. jerryjerry05

    Gimbal bearing is stuck on my u joint drive shaft

    When you install the drive: the o-rings on the shaft need grease but grease them after they get put on the shaft. Grease under the o-ring can lift the o-ring and can make it hard to install.
  14. jerryjerry05

    No electric getting to engine

    In the shifter the Neutral Safety switch might need attention? Try moving the shifter as you turn the key?? I don't think the AQ131 had a fuse in the system. They did have a fusible link, but this doesn't stop it from running. Test light?? Have someone at the key and try the connectors on the...
  15. jerryjerry05

    Turn off engine, wiring diagram. Help!

    The first pic has a foundry stamp. The circle with the 87 in the middle. 1987 Looks like Dec. or maybe January 1987?? The other # is a part# The last pic: no such thing as EFI on any Force :) You do a compression test? these 2cyl. can actually run fairly well on just 1 cyl. Any other ID#s...
  16. jerryjerry05

    Force 125 lacking power

    Usually any air leaks come from the port covers, once in a while the gaskets under the carbs. Things like electrical contacts need sanding, cleaning. All the connectors on the trigger and stator, if I have any question I replace them ALL. Just be careful as the trigger wires are very thin and...
  17. jerryjerry05

    Tilt Cylinders Leaking

    Like I said: it was a working cylinder when removed. Lets just hope it still works. Remember after it's all back together, GREASE the rod and the seal where the rod goes through. 99% DON'T lube the T@T and that causes failure. Last year I replaced the seals on 6 Yamahas and 3 Mercury's . They...
  18. jerryjerry05

    Slow crank

    FYI The 3/4 cyl. Forces when one plugs installed and you try to turn it over. The uneven compression can make it hard to turn. If one cyl. was bad it would have the same affect.
  19. jerryjerry05

    Turn off engine, wiring diagram. Help!

    rw504222 what's this # from? The pictures show a 1987-93 FORCE!! Post pics of the lower unit and the cowl. We need to figure out the year for the right wiring diagram. They used the same parts on most smaller Forces, The model# changes were usually small things like a different connector or...
  20. jerryjerry05

    I completely went down the rabbit hole with my cooling system Volvo Penta 5.7

    This post and the other one I couldn't find where you listed a year, model# or any way to ID the boat/motor?? A red motor, they were produced in the 80's What we working on? Pic of the drive?
Top