Search results

  1. jerryjerry05

    Hey Frank

    Thanks for the vote of confidence!!!!People like that keep us rebuilder in work :) Jerry
  2. jerryjerry05

    Primer enricher/new model Force

    Anyone know the procedure for testing it? I did but haven't done it for a while and need to make sure how. There is a diaphram in there that can rupture.HELP!!!
  3. jerryjerry05

    Did I get the wrong part for fill, vent, and drain plug on 85hp Force?

    Re: Did I get the wrong part for fill, vent, and drain plug on 85hp Force? The stand is for the lower unit while it's off. The extra oil was probably from the extra water it took in. They heat up and cool down. Heating up expands the oil/metal and it pushes oil out through seals. Cool down the...
  4. jerryjerry05

    HEY FRANK poerhead swap 88/95

    Would a powerhead from a 88/85 work on a 95/90 ??? Thanks,Jerry
  5. jerryjerry05

    89 Force 50 Exhaust Gaskets

    Re: 89 Force 50 Exhaust Gaskets Yes That one.See pic #1 Not really that hard.Just take lots of pics as you go.
  6. jerryjerry05

    Did I get the wrong part for fill, vent, and drain plug on 85hp Force?

    Re: Did I get the wrong part for fill, vent, and drain plug on 85hp Force? I made this in about an hour. Works great!!! Don't buy anything other than the impeller. The new drain plug gaskets might fix the leak. Weep holes? Could it be unburned gas/oil? Any leaks from the top of the drive could...
  7. jerryjerry05

    Force Cooling problems

    Re: Force Cooling problems Untill you get a manual.Look up a parts diagram boats.net has good diagrams. Any parts you need can probably be bought on this site. If it sat for 6yr the impeller should be replaced. The gear lube is drained and filled from the very bottom of the drive.There is a...
  8. jerryjerry05

    Houston...we have a problem....any advice or help?

    Re: Houston...we have a problem....any advice or help? Might be as simple as a bad head gasket.Or a rebuild. After the inspection and you find anything BIG then swap to the back up. Can be done in a day if you have a lift. Removing the flywheel after 20 yrs can be tricky.See pic that's how I do...
  9. jerryjerry05

    Did I get the wrong part for fill, vent, and drain plug on 85hp Force?

    Re: Did I get the wrong part for fill, vent, and drain plug on 85hp Force? The drain plug is a small allenhead socket screw.On the bottom of the drive. Don't remove the screw in the little hole on the side of the drive.See pics, The white washer on the VENT/FILL screw can be replaced with the...
  10. jerryjerry05

    compression, 35hp, force

    Re: compression, 35hp, force Not all the carbs had that spring.See pic!! It might not be missing. I'd check the fuel pump diaphram. Install a small filter between the carb and pump. Tilting the motor will allow fuel to escape as the float changes position.
  11. jerryjerry05

    omc

    Re: omc If you have the drive with the cone clutches,it's the best one there is.I wouldn't change it.It's the same as the Volvo or Bravo's The shift mech can get corroded and stick.The cable can corrode and not work right. #21/42 is called the bellcrank, it and the rest of the mech can get...
  12. jerryjerry05

    Boat wont pee? 1986 Force 50

    Re: Boat wont pee? 1986 Force 50 The 50 needs special muffs.See pic.It will overheat with regular muffs. Just as a precaution replace the impeller.Then rebuild the fuel pump and check/replace the hoses.Install a filter between the carb/pump.J
  13. jerryjerry05

    Help diagnose problem with Chrysler Economate 3.5HP

    Re: Help diagnose problem with Chrysler Economate 3.5HP Install a sparkie in line.Then see if your not getting any spark.They sell these at any auto parts place.Some cheaper some more expensive. No spark,then the flywheel comes off and the points need cleaning/sanding. Remember it sat for a...
  14. jerryjerry05

    Quick question

    Re: Quick question #38 If it pulls to the right turn it to the right.As you look from the back of the motor..
  15. jerryjerry05

    91, 50 HP Force water pump

    Re: 91, 50 HP Force water pump Not pumping water:could be the wrong muffs.Needs a special one. No idea why they won't work on Forces as they are the easiest $ there is. F433065-2 Part#. This site sells parts and if not boats.net is where i buy from/ They have a tech that answers any questions...
  16. jerryjerry05

    Pivot pin vs. Fill screws???

    Re: Pivot pin vs. Fill screws??? The screw on the side is a NO TOUCH.The allen head set screw on the bottom is the drain.
  17. jerryjerry05

    Tachometer problems

    Re: Tachometer problems Is there a dial on the back of the tach? See pic.If so try turning it when the motor is running. What color is the lead to the tach? Should be grey(I think) You need to jumper power (purple wire) and a ground to the terminals.Make sure they are connected right.J
  18. jerryjerry05

    50 hp force

    Re: 50 hp force The 50 needs a special set of muffs,the big ones won't work very well. Try running it in a bucket.J
  19. jerryjerry05

    85 Force 125 hp prop installation question

    Re: 85 Force 125 hp prop installation question The thrust hub goes on first.Then the prop,then the spacer and then the washer then the nut. The parts in the pic aren't the right stuff other than the thrust and spacer and nut. Prop is offa Merc. GOTTA have the right stuff!!! In that order.Or...
  20. jerryjerry05

    Local fish,Sebastian,Fl.

    Caught the flounder yesterday AM..The trout three days before.I caught a couple of trout 16@18 inch (no pic of them)the day after the pic. Using Top Pup.and various plastic and gig combos. Flounder and 2 trout right in front of my house.The 7 were caught down river. DELICIOUS!!!! The Tiger...
Top