Search results

  1. jerryjerry05

    Is this normal?

    Re: Is this normal? Get one of these.$6 almost anywhere auto parts are sold. 7/16 inch.
  2. jerryjerry05

    1980 85hp chrysler..$150?!

    Re: 1980 85hp chrysler..$150?! This type prop needs the hardware in the pic.Mercury prop in pic. Force is similar.No locking hub on Force. The older stuff won't fit the 86, the prop will go on,not the cone. They were made for the newer style,getting rid of the cone and flares.
  3. jerryjerry05

    motor SN location

    Re: motor SN location On the port side transom clamp. Usually they fall off and leave a rectangle patch on the side. You can see mine on the left.Been painted over.J
  4. jerryjerry05

    Overcharging.

    Force 88/125.Starts about 13v then the faster it goes the higher the voltage go'es.Levels off about 16.2 I'm thinking the regulator but I don't have access to the motor to test it.The owner said he's replaced the reg already. Any thoughts.The boats about 125mi away from me. Thanks,Jerry
  5. jerryjerry05

    What size nut on a 90hp flywheel ?

    Re: What size nut on a 90hp flywheel ? I use a BIG 3 jaw puller an impact wrench and a 2/3# hammer.See pic. Loosen nut,don't remove all the way. Insall puller and tighten as tight as it will go and then a bit more. Then hit with a hammer on the end of the puller bolt. Use gloves and keep your...
  6. jerryjerry05

    Junk parts!!

    Recently worked on a 125 Force.The guy spent $500 to have it FIXED at a local Ft.Lauderdale marina. They were supposed to change hoses and rebuild the carbs and do something minor like setting the timing.. They managed to change the hoses,no problem. The carbs were set wrong and the parts put in...
  7. jerryjerry05

    1974 chrysler 70hp motorl 707hf dies in 60 seconds

    Re: 1974 chrysler 70hp motorl 707hf dies in 60 seconds Absolutly BEAUTIFUL here!!! Tomorrow (Sunday)were going on our 2nd anual Toy Run.Should be a good ride.And not a hint of SNOW anywhere!!!! :) I've found that trying to adjust the kits usually ends up bad.Try cleaning up the old and check...
  8. jerryjerry05

    Is my boat suppose to have pee hole?? Force 40 1999

    Re: Is my boat suppose to have pee hole?? Force 40 1999 That motor might not have one.But you can install it easily. See pic #20 remove it and install an L shaped fitting and drill a small hole.Then a piece of hose.
  9. jerryjerry05

    1969 Chrysler 35 HP - New to Me, Runs Bad

    Re: 1969 Chrysler 35 HP - New to Me, Runs Bad Sometimes the only way to remove the flywheel is a BIG 3jaw puller. Wanna try this? I'll give instructions.J
  10. jerryjerry05

    1986 50 force

    Re: 1986 50 force NEVER start for any length of time.1 second can be too much!!!15 is way too long. That motor need s a special muff.The big one don't fit right see the pic.J
  11. jerryjerry05

    transom saver or what

    Re: transom saver or what There should be a trailer bracket for that motor. e-bay. See pic #24.You put it in place and lock it down with the lock switch. Probably easier to get the transom saver. Like Fucawi said if you have the room drive with it down.J
  12. jerryjerry05

    Changing over,Hey Frank??

    Changing over from the Manapower to the Prestolite. What parts need to be modified??? Frank you posted once about this.Can't find it. Thanks,Jerry
  13. jerryjerry05

    1982 Chrysler 85 No Spark help needed

    Re: 1982 Chrysler 85 No Spark help needed It takes a lot of force to remove the flywheel.It had 95# of tourqe on it. I use a BIG 3 jaw puller(see pic) and a 3/4# sledgehammer.The hammer in the pics is only a 2# use a bigger if you have one. Install the puller and leave the nut on a few...
  14. jerryjerry05

    Question about prop when in neutral, forward, & reverse

    Re: Question about prop when in neutral, forward, & reverse Hope this helps. Push down on the rod in the one pic.All the time spinning the prop either way.Then the prop pic.Pull up on the right hand side(one with the red thing)This will help spin the drive shaft. A pair of Vice-grips will work.
  15. jerryjerry05

    1990 Force 50 horse run issue

    Re: 1990 Force 50 horse run issue Do a compression/spark test.then rebuild the fuel pump. You running it in the lake or the drive?? The muffs you use could be the wrong ones.The right are in the pic I added. Check the impeller.Sounds like it's overheating.J
  16. jerryjerry05

    Starter problems???

    Just bought a 125/88 for parts.Owner said it hardly turns over and won't start. I replaced the starter with a back-up. I noticed the flywheel had a wobble(not supposed to).I removed it and saw the keyway was sheared. Cleaned up the keyway and used a good flywheel.The other 's magnet was...
  17. jerryjerry05

    Forgotten trim/tilt bracket

    Re: Forgotten trim/tilt bracket Pic of the lock bar. Send me your e-mail.J
  18. jerryjerry05

    Forgotten trim/tilt bracket

    Someone a while ago asked me about a tilt bracket.I promptly forgot. Well I was digging through my stuff and found it. Send me a PM and we'll talk.
  19. jerryjerry05

    Chrysler Economate 3.5 runs only at half-choke

    Re: Chrysler Economate 3.5 runs only at half-choke This might not be quit like your carb.#23/#16 Start with the carb.Take it apart and make sure there are no particals in the jets.No cloggs in the ports.A partical the size of a pin point can stop a motor from running.One time I cleaned a carb...
  20. jerryjerry05

    '87 50hp force flywheel problem(Am I Screwed?)

    Re: '87 50hp force flywheel problem(Am I Screwed?) You need a big 3 jaw puller.Install it and tighten it down and tighten it some more.Then with a hammer(oh yea reinstall the nut a little way)hit the threaded screw with the hammer. It should pop off.If not tighten it some more.I use an air...
Top