Search results

  1. jimmbo

    Testing thermostat with torch

    You will likely have to pull the Powerhead off the Exhaust Housing as that is likely where any pieces of the Impeller have gummed things up. O-rings should be considered expendable. However some have reused them, claiming they worked fine, but YMMV...
  2. jimmbo

    Testing thermostat with torch

    Blockage, or Waterpump, not working properly. Time to get the Tools out...
  3. jimmbo

    Testing thermostat with torch

    If you replace it, do test the new One is some Hot water....
  4. jimmbo

    Testing thermostat with torch

    It should be fully open by 145F
  5. jimmbo

    Estate sale lot of 18 - 25hp motors - Compression gauge variables.

    195psi.... ROTFLMAO:ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO::ROFLMAO:
  6. jimmbo

    Mercury BlackMax 175Hp, difficult staring, and then bogging down.

    Merc got the Extra Displacement by removing the Iron Sleeves from the 2 liter Block, and chroming the Bores. Pre 82, that displacement was for the 200 and 225, then in 82 when Merc started Prop Rating their bigger Outboards, the 2.4 black was used for the 175 and 200. Removal of the Iron...
  7. jimmbo

    Mercury BlackMax 175Hp, difficult staring, and then bogging down.

    On the 3rd you reported "I did a compression test and got readings 110, 125, 120, 115, 120, 125 which is average for a 2 stroke" 5 days later... " Recently it overheated again and this time scored one of the bores, see the attached image. I yet to do another compression test after this happen."...
  8. jimmbo

    I've got a 1971 Mercury 110 9.8hp outboard with a stuck tiller handle

    So you removed the Tiller Handle, and it is Frozen, or is the Part still part of the Engine still Frozen? As for the "other one on..." Is that a Complete Motor, or just the Tiller Handle?
  9. jimmbo

    Timing is retarded ;-)

    Why?
  10. jimmbo

    Timing is retarded ;-)

    You would have to speak to the Manufacturer/Engineers, as they are the Ones who had their Reason(s) to change the Number.
  11. jimmbo

    Timing is retarded ;-)

    Latest Parts Lists usually show the updates
  12. jimmbo

    Timing is retarded ;-)

    That # has been discontinued and superseded to 77-8M6008208
  13. jimmbo

    Timing is retarded ;-)

    I have no Problem using a GM labeled part, provided it is the Correct Part. I have seen many 3rd Party Parts that while the part was a GM Part, and it looked Identical, it wasn't the Correct Part. Years ago it was the same when it came to Carbs and Distributors, some people's Attitude, "it looks...
  14. jimmbo

    Timing is retarded ;-)

    Was it a Genuine Mercury Part, or a 3rd Party(including GM) Part?
  15. jimmbo

    1989 Mercury 200 Black Max

    Have you checked the wiring for shorts to Ground? Have you unhooked the Sensors/Sending units to see of it quits?
  16. jimmbo

    Estate sale lot of 18 - 25hp motors - Compression gauge variables.

    Early 80 Saws, to me are practically Brand New. When you said Old, I figured you meant something pre 1950
  17. jimmbo

    Estate sale lot of 18 - 25hp motors - Compression gauge variables.

    Felt Air Cleaner? For the past 50 years I have seen nothing but Foam Filters on Chain Saws, so that one you are referring to, must be really old
  18. jimmbo

    Prop Selection - Bayliner 175

    I reread the Thread, I didn't see anything Insulting...
  19. jimmbo

    Estate sale lot of 18 - 25hp motors - Compression gauge variables.

    The Bearings would be gummed up real quick
  20. jimmbo

    Prop Selection - Bayliner 175

    Maybe you need to get a Prop with Vent Holes to improve the Hole Shot
Top